crazycam425

Question: What is a shucked drive? These drives were in unraid since new and have been working fine for years. Recently I had other unraid issues and had to create a new config and that's when they stopped being seen by unraid.

I have 2 hard drives, that used to be in my array that unraid won't see now. Both drives are working with no smart errors and show up in unassigned devices when connected to unraid through a sata to usb adapter. However, when the drives are plugged directly into the motherboard or LSI controller they will not be seen by unraid. I ran a pre clear on each of the 2 disks while they were plugged into the sata to usb adapter and unraid still will not recognize them when they are plugged into the motherboard. Any ideas?

They do as long as I connect them to unRAID using an external sata usb connector. What would be the best way to move that data back to the array? Would I have to move the information share by share or is there something simpler?

Looking for help please! So I've made some mistakes and don't know what to do at this point to prevent data loss and restore unRAID as per how I used to have it. It all started with some simple changes that should not have affected anything. I added a HDD and LSI 9211-8i P20 IT Mode Sas controller. After I started unRAID back up it showed 1 device (disk1) missing from the array. So I restarted and the next time it showed 2 disks missing from the array. Then eventually 3 disks missing, then 2 again, and so forth. No rhyme or reason as to why different disks would be missing. Ultimately I tried to establish new config (without preserving disk assignments), which I know now was a mistake, and don't know what to do. So where i'm at right now is, the motherboard will not see 2 of my HDD's in the Bios. I've tried every combination of sata cables and power cables from working drives and the 2 will not show up no matter what. If I take a portable usb sata adapter and plug the drive into one of the motherboard usb ports, it shows up in unassigned devices just fine. So at this point the array is missing 2 drives with a lot of data on each and I have left the server off until I can figure this out as to prevent data loss. Can anyone please help or tell me where to begin. As far as the 2 drives not showing up in the motherboard bios, I'm tempted to think they'll show up again if I were able to format them, but at this point I don't want to do that as I will lose data.

Hi can anyone please tell me how to increase my docker img size without losing anything. I feel like this should be simple but I cannot find a thread anywhere explaining this. Thank you for the help!

That would be useful. On a side note, when I turn on tls-crypt openvpn defaults to the latest version of OpenSSL 2.4.3 and it Tunnelblick on my Mac I can change the OpenVPN version manually to whatever I need. However, the OpenVPN app I use on my iPhone only allows OpenVPN versions of 2.3.17 or lower. So if I have tls-crypt turned on I can only use Open VPN on my Mac and not my iPhone. So if you added Elliptic Curve to the app would it cause a similar issue? Because I would like to use tls-crpyt and Elliptic curve but I have to have Open VPN working on my iPhone as well so I can't right now.

I sent you the Diagnostics. How do I safely repair my flash drive without losing everything?

Can a flash drive go bad for just one app? How do you recommend I install it? I don't know how to fix this issue?

Sorry I'm still stupid but this is what I tried. I did view the file in Krusader and post that as well.

So you'll have to forgive me I'm not as technical as I wish I was but is this what you are asking?

It says that those directories do not exist?

Oh I forgot the contents of the folder. Here it is.

Ok so I tried a different folder name = didn't work Tried /etc/rc.d/rc.openvpnserver restart = Got an error Checked 3 boot package files = They are there. I posted to config files. Please let me know what else i can try. Thank you! openvpnserver_cert.cfg openvpnserver.cfg

Will do

I will try and let you know. I did follow the instructions and configure the server correctly and there was no start button. I will try to use a different folder name and see if that works and if not I'll post the 2 .cfg files. How do I out the Do I have to ssh in to do this?