chalk4

Members
  • Posts

    11
  • Joined

  • Last visited

Everything posted by chalk4

  1. This fixed the issue and I think I am good to go now. Thank you both for all the help!
  2. Thanks for this container. I have migrated the controller from my desktop to unRAID and it is working perfect!
  3. Thanks CHBMB! I did need to run the preview:generate-all first to generate the previews for the existing images. However it ran for a few minutes and then I get the PHP error above. When I try to rerun the command I get the same result. I have tried restarting the nextcloud docker too but it results in the same error. Error PHP Allowed memory size of 134217728 bytes exhausted (tried to allocate 12288 bytes) at /config/www/nextcloud/lib/private/legacy/image.php#477 in a few seconds Error PHP Allowed memory size of 134217728 bytes exhausted (tried to allocate 12288 bytes) at /config/www/nextcloud/lib/private/legacy/image.php#477 a minute ago Error PHP Allowed memory size of 134217728 bytes exhausted (tried to allocate 12288 bytes) at /config/www/nextcloud/lib/private/legacy/image.php#477 a minute ago Error PHP Allowed memory size of 134217728 bytes exhausted (tried to allocate 12288 bytes) at /config/www/nextcloud/lib/private/legacy/image.php#477 7 minutes ago Error PHP Allowed memory size of 134217728 bytes exhausted (tried to allocate 12288 bytes) at /config/www/nextcloud/lib/private/legacy/image.php#477 7 minutes ago Error PHP Allowed memory size of 134217728 bytes exhausted (tried to allocate 12288 bytes) at /config/www/nextcloud/lib/private/legacy/image.php#477 14 minutes ago Any idea why this is happening?
  4. Thank you! It is running now but I did get the following error: Error PHP Allowed memory size of 134217728 bytes exhausted (tried to allocate 12288 bytes) at /config/www/nextcloud/lib/private/legacy/image.php#477 When I tried to run it again it said the command is already running. I will let it run for a while and check the results.
  5. I have the app installed but I have no idea how to get the cron job setup properly. Thanks for the quick reply!
  6. Any chance we could have the Preview Generator built into this docker container? https://apps.nextcloud.com/apps/previewgenerator I am struggling to get this setup with the current docker container.
  7. Agreed. The new LSI should be here in a couple days. I will just have to deal with the reboots until it is installed.
  8. Well i rebooted and the speeds are sustained at 30+MB/sec. I have ordered the LSI card and will see if i run into any other issues once i have that installed. Thanks for the help fellas... much appreciated!
  9. Sorry for my ignorance. What are IRQ 17 and 18 used for and why would they be disabled?
  10. Thanks. Will the new LSI solve the Call Traces and IRQ 18 issues being reported? Would this card work fine? https://www.amazon.com/SAS9211-8I-8PORT-Int-Sata-Pcie/dp/B002RL8I7M Thanks for the help!
  11. I have recently installed Unraid and have been working to get everything setup correctly. I have been experiencing very slow transfer speeds while I was migrating data to the array. After some reading on the forum I removed the Parity disks and the write speeds seemed to improve from 2-4Mbit/Sec to 10-13Mbit/sec. I have recently ran the CA Fix Common Problems tool and the following errors appeared. It was recommended I post the diagnostics to the forums. Can anyone please assist? On another note I am trying to run unBALANCE for the first time and it is running at 1Mbit/sec, slower than any transfers I have had since I started. diagnostics-20170814-1215.zip