Hi,
i have some problem to get the smart informations get work on the unraid web interface
in the shell it works great:
root@Bunker:~# lsscsi -g
[0:0:0:0] disk Sony Storage Media PMAP /dev/sda /dev/sg0
[1:0:0:0] disk Hitachi HDS5C3030ALA630 R001 /dev/sdb /dev/sg1
[1:0:0:1] disk Hitachi HUA723030ALA640 R001 /dev/sdc /dev/sg2
[1:0:0:3] disk Seagate ST4000DM004-2CV1 R001 /dev/sdd /dev/sg3
[1:0:16:0] process Areca RAID controller R001 - /dev/sg4
[3:0:0:0] disk ATA Corsair Force GS 5.07 /dev/sde /dev/sg5
[5:0:0:0] disk ATA Hitachi HDS5C303 A5C0 /dev/sdf /dev/sg6
[8:0:0:0] disk ATA ST4000DM004-2CV1 0001 /dev/sdg /dev/sg7
[8:0:1:0] disk ATA ST4000DM004-2CV1 0001 /dev/sdh /dev/sg8
The Smartctl:
root@Bunker:~# smartctl --all --device=areca,1 /dev/sg4
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.14.49-unRAID] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 5K3000
Device Model: Hitachi HDS5C3030ALA630
Serial Number: MJ1311YNG4KDGA
LU WWN Device Id: 5 000cca 228c212cf
Firmware Version: MEAOA5C0
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5700 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sun Jul 15 11:55:32 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (36667) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 611) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 133 133 054 Pre-fail Offline - 115
3 Spin_Up_Time 0x0007 127 127 024 Pre-fail Always - 550 (Average 549)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 524
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 132 132 020 Pre-fail Offline - 32
9 Power_On_Hours 0x0012 095 095 000 Old_age Always - 38994
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 77
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1105
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 1105
194 Temperature_Celsius 0x0002 150 150 000 Old_age Always - 40 (Min/Max 18/48)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
so i set it up in unRiad
and unRaid get this error
any idea to resolve this?