Lenny Warren

Thanks, I force updated Resilio and it seemed to work.... will keep an eye on it. Do the container sizes in the above screengrab seem small for Resilio, should I and how do i increase it?

I force updated Resilio and it cleared the log. I've set the Docker log to rotate, but I'm presuming this is a different log which is just for Resilio? Is there a way to keep the Resilio log at a smaller size?????

Looks like it is the Resilio log? Any idea how to remove the log?

Rebooting the server doesn't clear it, so thinking it's not actually memory, it's data filling the docker container?

Thanks, but how do I sort that?

Hi folks, I've stared used Resioio Sync but as it works through syncing files from my synology NAS to my UM+NRAID, the Docker memory usage rises substantially, eventually up to 100% and then it falls over. Is it using the memory as cache, or ???? HELPPPPPPP.... I get this warning... Docker high image disk utilization: 13-04-2019 08:00 Warning [ARCHIVE-2] - Docker image disk utilization of 73% Docker utilization of image file /mnt/user/system/docker/docker.img

Hi there, I accidentality unplugged one of my drives whilst array was running, yes I know I shouldn't have... Anyway, re-connected it and now it shows up as Disk 1, but it has a red X next to it and says "DEVICE IS DISABLED, CONTENTS EMULATED." How do I re-enable it? seems strange. the m/b BIOS finds the drive ok, just UNRAID has it diabled....

Cheers, I’ve ordered a pre-flashed H200 from eBay. ?

So why is that? Does it give issues? if I bought a H200 or H310 already flashed to IT mode would it be plug and play? Plug into existing cabling and still use the existing backplane? Heres the inside of my R610...

I'm setting up a DELL Poweredge R610 with H700 RAID controller. Set up each individual drive as RAID 0, and in UNRAID it finds drives and allocates them. I've read that UNRAID doesn't like the H700, why is this? Will it cause issues? It seems to be working fine...

Weirdly enough, UNRAID finds the PERC H700 drives... Thought this wasn't meant to work?

Weirdly enough, I reformated the flash card, started from scratch with the Unraid boot creator and it worked fine, bizarre.... ? Thanks for advice though, must have been corrupted flash card?

It's as if the NICs aren't there...

Green light at NICs and switch. Swapped cables and ports around, still the same... I'm wondering id there's a weird setting in the R610 BIOS, got lots of oprions for NICs..

I have two Ethernet cables attached, maybe something to do with "cannot find bond 0" ????

My main UNRAID is working well, but tried a new build today and having issues... PIcked up a DELL Poweredge R610, which has the H7000 raid controller. Not worried about that at the moment, will either flash it or replace with a PICe sata controller. Anyway, I make a USB boot flash drive with the OSX creator, I set a server name, ARCHIVE-3. I've tried both with DHCP and also manually assigned IP, however when I boot I get the usual unRAID startup, and all is well at the console control prompt. However, the server name has defaulted to Tower and a random ip address outwith what my DHCP server is set for. It is saying 169.254.209.20 when I tried to set it for 192.168.0.40 If I try to login at console with root.(blank) it logs in ok, but can't find the webGUI at either Tower.local or 169.254.209.20 If I try the UNRAID GUI it doesn't find the GUI either.... Any thoughts? Strange why the server doesn't act on the flash boot config???

Newbie to UPS's... I picked up a 2nd hand APC Smart-UPS 750 Connected with a standard USB cable to my server, DELL Poweredge T310. Autodetect found it, all seems ok, but Nominal Power, UPS Load and UPS Load % are blank. If I switch display settings to manual, and add VA and watts I then get Nominal Power to display 500, but not Load or load % Do I need a special USB cable, or ????

unRAID 6.5.3 on a Dell Poweredge T310, 32Gb RAM... I used Krusader to synchronise a directory on my Synology NAS. Around 9TB, took about 5 days. So, Krusader reports the 9Tb moved over, it shows up in unRAID but the file info in OSX finder doesn't show the total, only 1.09Tb All the files (images) seem to be there, but OSX doesn't report the true filesize. Is this an issue with how I moved them, from Krusader?

Cheers, appreciated.

Excellent, that worked. Many thanks. So use cache:only causes issues???

Doing that now, do you mean settings-docker-enable docker-no ? Running mover now, thanks for this...

Hi there, New to unRAID. My server is working fine, however I ran the plugin Fix Common Problems. I get the following warning.. Share appdata set to cache-only, but files / folders exist on the array I had previously had appdata on a standard share, but now I've changed my appdata share to be cache only but can't seem to move the appdata directory through Krusader. Even if I try to move it to the Trashcan, Krusdaer just takes forever and doesn't seem to work. I'm not up tp speed on doing it from the command line, but any thoughts? Cheers, Lenny