GurKeSaLaT

Hello, I'v had some Issues with my Setup lately (frozen Webui/Crashes/etc). After some research I found out, that it had to do with my Docker macvlan. I tried using ipvlan, but it dosen't work, because my Router/firewall (pfsense as a VM with dedicated 4-port NIC). I couldn't get the containers to be reachable from the outside, while internaly seperating them from the rest of the network. Now I tried to disable the bridge on eth0 and all my dockers are running fine now, but my VMs have connection to everything but the host. I can reach the internet and my other Services on my network just as expected. The only thing I cannot reach is my UNRAID-Box. I cannot even ping it. I even tried to add a custom virtial bridge between my VMs and added a virtual NIC on my pfsense. I still can access the everything via the virtual network between my VMs but still cannot reach my UNRAID. I would like to keep eth0 unbridged since this lets me use all of my dockers, but I still need connection to UNRAID from my VMs. I hope somebody can help. tower-diagnostics-20240227-0908.zip

Ok, i got a new Mainboard and not everything is working again. Thanks for the support!

Damn, I switched powersuplys, but it is still freezing. Now I orderd a new Mainboard, I hope it' not the processor. I'll report back when i tested the new board. Thanks for the help this far!

Here are new diags. I think by now it is even faster freezing, sometimes there is not even enough time to get the array started now. syslog-192.168.0.10 (8).log tower-diagnostics-20230822-2115.zip

I tried every USB-Port but still freezing. Then i Tried a new USB-Key, and it still keeps freezing. I doubt it has something to do with the controler on the Mainboard, i got a extra USB-Card which I normaly pass into a VM, so i can hotplug, but even in those ports its freezing after a short while. Any other Ideas?

Thanks for the response, will try different USB-Ports this evening. Can you name me a tool to test the USB-Key? I Thinks it is about 7 years old, maybe it is dying.

Hello, I was on holidys and came back home to a frozen Server. So I have no exact point of time wehen this started to occur. This server was runing with this config for about a year now, no problems what so ever. I can start the server normaly. I have autostart of the array of, because I use encypted disks and have to add the keyfile. After I add the keyfile and start the array, it comes up normaly, all Docker container and VMs start normaly. I tried allready booting, in safemode, still freezing after some time. I disabled docker and VMs, still freezing. some odd things i encountered: 1. My Main VM had a "unkown USB Device" and could not start at the first try, but i removed the device from the config an not it is starting normaly with the rest. 2. I had some CRC errors on one of my drives in a seperate pool. So I remoed the drive, and started the server againe, bit still freezing after some time. Now I added the drive back to the pool, without any problems. 3. Sometimes all my devices in pools get unassigned and i need to reassign them. I tried memtest allready and let it run for 5 passes without any errors. Since i use a seperate nvme SSD which is passed thout to my main VM seperatly I also tried booting from that and it worked (had some problems because none of the Networkshares are there, but it ran an showed all drives. Let it sit in Idle for about 2h. Therefor I don't think it's a Hardware problem. Edit: I also have no overclock, and c-state is set to "typical current idle" Atatched diagnostics after array start. And also some Logfiles I gathered after turning on the logserver. Can anybody help me to figure out what's the problem with my server? If you need any more Info please let me know. syslog-192.168.0.10.log tower-diagnostics-20230821-2124.zip

Thank you, I ordered a new cable and will report back in a few days.

Maybe you can help me with that. The tape on the left side was wraped arround the cable. The Text says: MOLEX 79576-3002 MADE IN CHINA 07/13

Is there any way to tell the differenz, because i just use the cable that came with the card? I don't have a second cable and the bundle is used so maybe they put the wrong cable in there.

Even if I had the RAID firmware, I would see the drives in the controller BIOS, wouldn't I?

I flashed it with IT firmware.

Hey guys, I bought a H310 controller and flashed it to the LSI firmware. Got some problems during the process becaus I had a UEFI an got the PAL-error, so I put the controller in my old mobo and flashed using FreeDOS without any further problems. Now with the new firmware I put it back in my server and hooked up 3 drives to it, the problem is now that no drives are detected not in UnRaid nor in the BIOS of the controller. The controller itself gets detected within UnRaid, just no drives. Any Ideas what went wrong? If you need more data please let me know, I'm new to UnRaid and other server-stuff.