Popple2000

Thanks for the reply :) I'm not sure how to do that. I try not to muck around too much without guidance in fear of breaking something.

I found the "Docker Patch 6.12.8" and all seems well now. Thanks!

Hey guys, I just updated a bunch of dockers and plex/tailscale etc have vanished. I went to the apps tab to reinstall them, but when I do, I get "docker: invalid spec: :/downloads:rw: empty section between colons." Can anyone help please? Thanks

Thanks @JonathanM I looked quickly and didn't see anything. I'll give that a try.

Hey guys, After I last updated the container I was no longer able to connect to ombi etc from outside the network. When I checked the logs I'm getting this over and over. "nginx: [emerg] "stream" directive is not allowed here in /etc/nginx/conf.d/stream.conf:3" Is there a quick fix for this? Please let me know if more info is required. Thanks!

@trurl I moved the second cache drive off the LSI HBA and onto the onboard sata and i think that solved the trim issue(I read somewhere that could be the culprit) Im pretty sure the rest of my issues are solved for now as well. Thanks for your help! Cheers beafy-diagnostics-20220315-0838.zip

Hey, I had no sync errors. I'll go ahead and update to UDP. I was emptying the drive to convert it to XFS and then swap in a 14tb i have sitting here. As far as sdj1 is concerned, can I do anything to remedy the trim error? Should I be concerned?beafy-diagnostics-20220313-1624.zip *edit* Perhaps you were talking about the critical target error... I assume this is bad? Should I replace the drive? *edit 2* I ran a scrub and balance, updated everything, cleaned up the errors I could, rebooted the server and attached a new diag.

I was using unbalance to move files off a disk and I must have miss-clicked something because it started deleting everything off the disk instead and I couldn't get it to stop, so I initiated a reboot from the unraid GUI. When the server came back up from it's reboot it was running a parity check on it's own so I assume something went wrong with the reboot.

I will, thanks so much!

Wow, in my panic I didn't even realize it was referencing that fossil of a plugin. Thanks so much!

Hey guys, I received "Your flash drive has possible corruption on /boot/config/plugins/plexmediaserver/settings.ini" today from Fix Common Problems after formatting a disk and restarting the array. I've attached the diag and was hoping someone could tell me if I should panic or not. beafy-diagnostics-20220313-1502.zip Many thanks in advance!

Amazing! All fixed for now! Thanks so much!

I'm currently reading through the thread as you sent this - Thanks!

Thanks for that, I guess I'll just wait it out. Appreciate the heads up

Hello all! So, I recently added a 10TB Parity drive(not sure if that has anything to do with this) and since then, my DOCKER tab when I click "check for updates" shows: This looked fairly normal to me since I hadn't updated my containers in a while. I ran "update all"(same outcome if I try to update individually) and all of the "pulling image" boxes looked like this: 0 b pulled every time.(aside from when there actually is an update, as it seems to be updating if one is actually available) Once I run the updated and it finishes, all of the containers show up to date, but if I run "check for updates" again, they all show as if they need to be updated once again. Thanks in advance for any help and please don't hesitate to ask if you need more information!

Updated from 6.6.7 smooth as butter. Thanks guys, looks great!

Thanks! Love his videos too!

Thanks!

If i hooked them both up at the same time, there would be nothing on them. I was wondering if the above mentioned technique would save me a backup and restore. But thanks for your reply!

Hi there. I have a scenario I'd like to ask about. Currently I have 2x 128gb ssd's in a btrfs cache pool but I would like to upgrade to two 500gb's Could I pull one of the 128gb out, drop in a 500gb, let it balance.... then pull out the other 128, drop in the other 500gb and let it balance again? Or would this not work? Thanks in advance.

Let me ask you this... If someone was watching something on plex and it was transcoding... should that affect the xfer speed? I should mention that I have the transcoding going to ram, not the ssd. Could it be an I/O conflict? I am at a loss

I agree with this statement 100%! lol Hence my ongoing frustration

Transferring between all the other PC's on my network is fine, as is a direct transfer to any disk in my array other that the cache drive...

The 30g xfer jsut shot up to 65MB/s out of nowhere? now its back down to 23

I also just transfered a file from my desktop to disk7 directly and it went at 60MB/s and the xfer to the cache slowed down to 5MB/s and then went back to 25MB's when the direct xfer finished