Jon4got2 Posted March 10, 2022 Share Posted March 10, 2022 Hello. I ran into something similar almost a couple years ago, coincidentally I had covid then and just got it now again, and the brain just does not function well with this so please bare with me if you could. I'm running Version: 6.10.0-rc2 mobo: Asus PRIME Z590 processor: i5-11600K HBA: (2) LSI SAS3008 Things have been smooth sailing for the last couple years, but a couple days ago a drive (#5) was throwing up errors. I pulled the drive, cleaned the contacts, reinstalled and ran a smart test which came back fine. I formatted the drive and re-added to the array. In the middle of rebuilding the drive, another disk (#7) started throwing errors. Like a dummy, I stopped the rebuild of #5 about 1/4 way through before the #7 disk had totally failed an was disabled, powered down and cleaned the connections to that one. Rebooted and #7 was disabled. I tried running xfs repair and got: superblock read failed, offset 0, size 524288, ag 0, rval -1 fatal error -- Input/output error I'm currently running an extended smart test on that one. It's obviously a rare chance that 2 drives failed at the same time, so I'm guessing it's a HBA or something to that effect, but my foggy brain is having issues troubleshooting at the moment. I'm hoping someone can poke through these logs and point me in the right direction. I only have one parity drive and really hope I can at least get #7 back up so I can rebuild #5. I truly appreciate your help! Jon tower-diagnostics-20220310-1200.zip Quote Link to comment
JorgeB Posted March 10, 2022 Share Posted March 10, 2022 Unraid can't emulate two disks with single parity, this is a scenario that should not happen, i.e., disabling one disk during the rebuild of another with single parity, disk7 look OK, though there are a lot of CRC errors, if these are recent you should replace the SATA cable, then you can force enable disk7 to try and rebuild disk5, assuming parity is still valid, to do that: -Tools -> New Config -> Retain current configuration: All -> Apply -Check all assignments and assign any missing disk(s) if needed -IMPORTANT - Check both "parity is already valid" and "maintenance mode" and start the array (note that the GUI will still show that data on parity disk(s) will be overwritten, this is normal as it doesn't account for the checkbox, but it won't be as long as it's checked) -Stop array -Unassign disk5 -Start array (in normal mode now), ideally the emulated disk will now mount and contents look correct, if it doesn't you should run a filesystem check on the emulated disk -If the emulated disk mounts and contents look correct stop the array -Re-assign disk5 and start array to begin. Quote Link to comment
Jon4got2 Posted March 10, 2022 Author Share Posted March 10, 2022 Thanks Jorge! Okay I got all that to work except then it asked me to format disk #5, so I did. Now it still says "unmountable" and asking to format again. Tried selecting xfs file system, but no luck. Any ideas? Quote Link to comment
JorgeB Posted March 10, 2022 Share Posted March 10, 2022 Don't format, post new diags after array start. Quote Link to comment
Jon4got2 Posted March 10, 2022 Author Share Posted March 10, 2022 new diag attached tower-diagnostics-20220310-1200.zip Quote Link to comment
JorgeB Posted March 10, 2022 Share Posted March 10, 2022 You didn't do the procedure correctly, or those are old diags, both disks are still invalid. Quote Link to comment
Jon4got2 Posted March 10, 2022 Author Share Posted March 10, 2022 when i restarted without disk 5, it was not emulated. just showing "not installed" and "unmountable" Quote Link to comment
JorgeB Posted March 10, 2022 Share Posted March 10, 2022 You didn't do the new config, both disks are still invalid. Quote Link to comment
JorgeB Posted March 10, 2022 Share Posted March 10, 2022 Follow the instructions above carefully. Quote Link to comment
Jon4got2 Posted March 10, 2022 Author Share Posted March 10, 2022 I definitely did the new config. got to where all the blue boxes were next to the drives and restarted the config. I just went through and did it all again. I attached another set of diag. tower-diagnostics-20220310-1347.zip Quote Link to comment
Jon4got2 Posted March 10, 2022 Author Share Posted March 10, 2022 looks like i may have uploaded the 1st one twice like you suspected. sorry about that. (foggy brain) Quote Link to comment
JorgeB Posted March 10, 2022 Share Posted March 10, 2022 OK, I can see disk7 is now enable but due to log spam from the previous issues can't see the latest lines, reboot and post new diags after array start. Quote Link to comment
Jon4got2 Posted March 10, 2022 Author Share Posted March 10, 2022 this time after i formatted #5, it mounted properly and seems to be rebuilding and not throwing errors on #7. I'll let this run through and hopefully the second time was the charm. If it doesn't take I'll reboot and send you those diags. Thanks again for your help. I really appreciate it! Quote Link to comment
JorgeB Posted March 10, 2022 Share Posted March 10, 2022 4 minutes ago, Jon4got2 said: this time after i formatted #5 46 minutes ago, JorgeB said: Don't format Unless there was nothing important on that disk, or all data there will be gone. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.