rematch Posted October 28, 2023 Share Posted October 28, 2023 (edited) I am new to Unraid and have already read through many posts. Frankly, however, I am quite overwhelmed and do not want to make mistakes right at the beginning, hence the question. Unraid runs on a Lenovo M720q server, on which unfortunately only two NVMe and one SSD (SATA) can be installed. So the server has the following three hard drives: - Samsung SSD 980 PRO 1TB, M.2 2280 - KIOXIA BG5 Client SSD 1TB, M.2 2230-S3 - SSD with 512 GB (Noname) How should I best set up Unraid with the three hard drives (data, parity, cache)? Using Unassigned Devices I included my Synology NAS (which has 4x 4TB HDD) as SMB share; but there I'm not sure yet how to use that. Can I use this storage? Otherwise, I would just run backups to the NAS, if possible (via CA Appdata Backup?). The NAS is backed up daily (to another location). At this stage, I would rather run services on the server to make my life easier. I'm sure there will be relevant data, but it should be backed up by regular backups. So it would not be dramatic if, in the worst case, everything would be gone. But this is only further information. Thank you very much. Edited October 28, 2023 by rematch Quote Link to comment
rematch Posted October 29, 2023 Author Share Posted October 29, 2023 /push I would really appreciate some guidance so I can finally get started - thanks! Quote Link to comment
JorgeB Posted October 29, 2023 Share Posted October 29, 2023 With those three devices I would assign an old flash drive as the single array device to fulfill that requirement then assign the 3 SSDs to two or three pools depending on your needs, e.g., you can create a redundant pool with both 1TB devices and another one for the 512GB device, or 3 separate pools. Quote Link to comment
rematch Posted October 29, 2023 Author Share Posted October 29, 2023 I see, thank you. Unfortunately, I don't have another old flash drive, only these three I mentioned. How would you setup data, cache and parity with these? Is Parity even needed, regarding the Synology Backup? Could I go with, e.g.,: - 1 TB NVMe for Data (KIOXIA) - 1 TB NVMe for Cache (Samsung Pro) - 512 GB SSD for Cache I just don't understand what to assign to which hard disk. Quote Link to comment
itimpi Posted October 29, 2023 Share Posted October 29, 2023 13 minutes ago, rematch said: Unfortunately, I don't have another old flash drive, only these three I mentioned. This is a pen drive of the type that you boot Unraid from - can be very small (only a a few GB) as you are not going to store anything on it, merely use it to satisfy the requirement (in the current Unraid release) that there must be at least one drive in the array. This restriction is planned to e lifted in a future Unraid release but this is a way to get around it at the moment. Quote Link to comment
rematch Posted October 29, 2023 Author Share Posted October 29, 2023 2 minutes ago, itimpi said: This is a pen drive of the type that you boot Unraid from - can be very small (only a a few GB) as you are not going to store anything on it, merely use it to satisfy the requirement (in the current Unraid release) that there must be at least one drive in the array. This restriction is planned to e lifted in a future Unraid release but this is a way to get around it at the moment. Oh, you mean the typically USB drive. Ok, sure, I can do it, thanks for the hint. But still, would this: 19 minutes ago, rematch said: Could I go with, e.g.,: - 1 TB NVMe for Data (KIOXIA) - 1 TB NVMe for Cache (Samsung Pro) - 512 GB SSD for Cache ... be ok to host data and cache? Or what is recommended? Quote Link to comment
JorgeB Posted October 29, 2023 Share Posted October 29, 2023 1 hour ago, JorgeB said: assign the 3 SSDs to two or three pools depending on your needs, e.g., you can create a redundant pool with both 1TB devices and another one for the 512GB device, or 3 separate pools. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.