Benji Posted December 4, 2023 Share Posted December 4, 2023 (edited) I've just had a drive rack up some read errors. I assume the disk is toast and needs replacing, but I just wanted to double check. If it is faulty, I don't currently have a hot/cold spare. So far I've excluded it from every share that uses the array. Would the best protocol be to just leave it and rebuild when I get a new drive or try and copy data off it? Many thanks. apollo-diagnostics-20231204-1308.zip Edited December 4, 2023 by Benji Quote Link to comment
ChatNoir Posted December 4, 2023 Share Posted December 4, 2023 10 minutes ago, Benji said: I've just had a drive rack up some read errors. Can you tell us what drive in particular ? I'm not so keen on searching in the 23 drives. Ideally try to run an extended SMART test and post the result. 1 Quote Link to comment
Benji Posted December 4, 2023 Author Share Posted December 4, 2023 1 minute ago, ChatNoir said: Can you tell us what drive in particular ? I'm not so keen on searching in the 23 drives. Ideally try to run an extended SMART test and post the result. Oh, sorry. Drive 13. I'll do that. Quote Link to comment
ChatNoir Posted December 4, 2023 Share Posted December 4, 2023 I see a single attribute that is problematic. ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 100 051 - 9 Let's see the result of the SMART test. 1 Quote Link to comment
ChatNoir Posted December 4, 2023 Share Posted December 4, 2023 Ok, I'm bored in my meeting. Disk 16 looks worst on attributes 1 and 200. ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 101 3 Spin_Up_Time POS--K 253 253 021 - 8341 4 Start_Stop_Count -O--CK 093 093 000 - 7191 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 017 017 000 - 60806 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4730 192 Power-Off_Retract_Count -O--CK 200 200 000 - 206 193 Load_Cycle_Count -O--CK 198 198 000 - 6984 194 Temperature_Celsius -O---K 111 091 000 - 41 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 Quote Link to comment
Benji Posted December 4, 2023 Author Share Posted December 4, 2023 5 minutes ago, ChatNoir said: I see a single attribute that is problematic. ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 100 051 - 9 Let's see the result of the SMART test. I thought extended tests took longer. Either way, I got notified of a read failure and the test completed. Spoiler smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.63-Unraid] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Se Device Model: WDC WD6001F9YZ-09YUWL1 Serial Number: WD-WXB1HB4RA0XX LU WWN Device Id: 5 0014ee 26272581d Firmware Version: 01.01E03 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Dec 4 13:37:14 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 90) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 567) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 100 051 - 9 3 Spin_Up_Time POS--K 197 100 021 - 9116 4 Start_Stop_Count -O--CK 100 100 000 - 73 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 100 000 - 0 9 Power_On_Hours -O--CK 014 014 000 - 63054 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 73 16 Unknown_Attribute -O---K 124 076 000 - 2195536296398 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 100 000 - 54 193 Load_Cycle_Count -O--CK 196 100 000 - 13993 194 Temperature_Celsius -O---K 112 096 000 - 40 196 Reallocated_Event_Count -O--CK 200 100 000 - 0 197 Current_Pending_Sector -O--CK 200 100 000 - 1 198 Offline_Uncorrectable ----CK 200 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 8 Device Statistics Notification 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x24 GPL R/O 171 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xaf GPL,SL VS 16 Device vendor specific log 0xb0 GPL,SL VS 1 Device vendor specific log 0xb1-0xb5 GPL,SL VS 16 Device vendor specific log 0xb6 SL VS 16 Device vendor specific log 0xb7 GPL,SL VS 40 Device vendor specific log 0xb8-0xbf GPL,SL VS 16 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xde GPL VS 5502 Device vendor specific log 0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 13 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13 [12] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 28 00 01 b9 98 da 30 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 12 [11] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 02 c8 00 01 b9 98 c3 e8 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 11 [10] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 02 40 00 01 b9 98 cf 08 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 10 [9] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 01 f0 00 01 b9 98 b8 d0 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 9 [8] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 03 d8 00 01 b9 98 ad b0 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 8 [7] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 02 10 00 01 b9 98 97 78 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 7 [6] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 04 00 00 01 b9 98 8c 58 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 6 [5] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 04 00 00 01 b9 98 81 40 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 63053 157410704 # 2 Short offline Completed without error 00% 63053 - # 3 Extended offline Aborted by host 90% 55628 - # 4 Short offline Completed without error 00% 55628 - # 5 Short offline Completed without error 00% 55627 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 31/41 Celsius Lifetime Min/Max Temperature: 16/56 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (49) Index Estimated Time Temperature Celsius 50 2023-12-04 05:40 40 ********************* ... ..( 89 skipped). .. ********************* 140 2023-12-04 07:10 40 ********************* 141 2023-12-04 07:11 41 ********************** ... ..( 2 skipped). .. ********************** 144 2023-12-04 07:14 41 ********************** 145 2023-12-04 07:15 40 ********************* ... ..( 23 skipped). .. ********************* 169 2023-12-04 07:39 40 ********************* 170 2023-12-04 07:40 41 ********************** ... ..( 3 skipped). .. ********************** 174 2023-12-04 07:44 41 ********************** 175 2023-12-04 07:45 40 ********************* ... ..( 84 skipped). .. ********************* 260 2023-12-04 09:10 40 ********************* 261 2023-12-04 09:11 41 ********************** ... ..( 31 skipped). .. ********************** 293 2023-12-04 09:43 41 ********************** 294 2023-12-04 09:44 40 ********************* ... ..( 20 skipped). .. ********************* 315 2023-12-04 10:05 40 ********************* 316 2023-12-04 10:06 41 ********************** ... ..(183 skipped). .. ********************** 22 2023-12-04 13:10 41 ********************** 23 2023-12-04 13:11 40 ********************* ... ..( 9 skipped). .. ********************* 33 2023-12-04 13:21 40 ********************* 34 2023-12-04 13:22 39 ******************** ... ..( 9 skipped). .. ******************** 44 2023-12-04 13:32 39 ******************** 45 2023-12-04 13:33 40 ********************* ... ..( 3 skipped). .. ********************* 49 2023-12-04 13:37 40 ********************* SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 73 -D- Lifetime Power-On Resets 0x01 0x010 4 63054 -D- Power-on Hours 0x01 0x018 6 526341730843 -D- Logical Sectors Written 0x01 0x020 6 3628488940 -D- Number of Write Commands 0x01 0x028 6 1669194565555 -D- Logical Sectors Read 0x01 0x030 6 9882246389 -D- Number of Read Commands 0x01 0x038 6 3656100608 -D- Date and Time TimeStamp 0x01 0x048 2 12490 ND- Workload Utilization 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 63053 -D- Spindle Motor Power-on Hours 0x03 0x010 4 53475 -D- Head Flying Hours 0x03 0x018 4 14048 -D- Head Load Events 0x03 0x020 4 200 ND- Number of Reallocated Logical Sectors 0x03 0x028 4 866 -D- Read Recovery Attempts 0x03 0x030 4 0 -D- Number of Mechanical Start Failures 0x03 0x038 4 8 -D- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 54 -D- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 9 -D- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 -D- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 40 -D- Current Temperature 0x05 0x010 1 38 -D- Average Short Term Temperature 0x05 0x018 1 39 -D- Average Long Term Temperature 0x05 0x020 1 56 -D- Highest Temperature 0x05 0x028 1 17 -D- Lowest Temperature 0x05 0x030 1 53 -D- Highest Average Short Term Temperature 0x05 0x038 1 25 -D- Lowest Average Short Term Temperature 0x05 0x040 1 45 -D- Highest Average Long Term Temperature 0x05 0x048 1 34 -D- Lowest Average Long Term Temperature 0x05 0x050 4 0 -D- Time in Over-Temperature 0x05 0x058 1 60 -D- Specified Maximum Operating Temperature 0x05 0x060 4 0 -D- Time in Under-Temperature 0x05 0x068 1 0 -D- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 41 -D- Number of Hardware Resets 0x06 0x010 4 41 -D- Number of ASR Events 0x06 0x018 4 0 -D- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 0 Vendor specific Quote Link to comment
JorgeB Posted December 4, 2023 Share Posted December 4, 2023 That disk should be replaced. 1 Quote Link to comment
Benji Posted December 4, 2023 Author Share Posted December 4, 2023 Just now, JorgeB said: That disk should be replaced. Yeah, I figured. Thank you. Quote Link to comment
ChatNoir Posted December 4, 2023 Share Posted December 4, 2023 You should run an extended SMART test on disk16 to be sure. 1 Quote Link to comment
Benji Posted December 4, 2023 Author Share Posted December 4, 2023 Just now, ChatNoir said: You should run an extended SMART test on disk16 to be sure. I'll do that as well, thank you. Quote Link to comment
Benji Posted December 4, 2023 Author Share Posted December 4, 2023 The SMART test is running on disk 16, but the more I think about it, the more I'm tempted to just pre-emptively remove it. Can I replace disk 13 and remove disk 16 at the same time or would I have to replace 13 and then remove 16? Quote Link to comment
ChatNoir Posted December 4, 2023 Share Posted December 4, 2023 8 minutes ago, Benji said: Can I replace disk 13 and remove disk 16 at the same time or would I have to replace 13 and then remove 16? If you have double parity, you should be able to do both (I never had to do it yet ^^). 1 Quote Link to comment
Benji Posted December 4, 2023 Author Share Posted December 4, 2023 (edited) 1 minute ago, ChatNoir said: If you have double parity, you should be able to do both (I never had to do it yet ^^). I do. I'm replacing the 6TB 13 with a 10TB disk, so even removing the 2TB 16 I'd still be up 2TB overall. That one hadn't thrown errors yet, I appreciate you bringing it to my attention. Edited December 4, 2023 by Benji Quote Link to comment
ChatNoir Posted December 4, 2023 Share Posted December 4, 2023 For WD drives, you should add attributes 1 and 200 to the monitored attributes. That way, Unraid will alert you if new errors are detected. They are not monitored by default as Segate manages them differently. 1 Quote Link to comment
Benji Posted December 4, 2023 Author Share Posted December 4, 2023 I didn't know that was an option, I shall do that now. Thank you again! Quote Link to comment
Benji Posted December 10, 2023 Author Share Posted December 10, 2023 While preparing stuff to swap the disk out, the raw read errors have all disappeared. The SMART stats show no errors now and it passed an extended test without issue. Should I still be wary of this disk and swap it out anyway? Here's the most recent test: Spoiler smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.64-Unraid] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Se Device Model: WDC WD6001F9YZ-09YUWL1 Serial Number: WD-WXB1HB4RA0XX LU WWN Device Id: 5 0014ee 26272581d Firmware Version: 01.01E03 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Dec 10 12:56:06 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 90) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 567) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 100 051 - 0 3 Spin_Up_Time POS--K 197 100 021 - 9125 4 Start_Stop_Count -O--CK 100 100 000 - 74 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 100 000 - 0 9 Power_On_Hours -O--CK 014 014 000 - 63195 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 74 16 Unknown_Attribute -O---K 125 075 000 - 2197617489628 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 100 000 - 56 193 Load_Cycle_Count -O--CK 196 100 000 - 14459 194 Temperature_Celsius -O---K 113 096 000 - 39 196 Reallocated_Event_Count -O--CK 200 100 000 - 0 197 Current_Pending_Sector -O--CK 200 100 000 - 0 198 Offline_Uncorrectable ----CK 200 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 8 Device Statistics Notification 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x24 GPL R/O 171 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xaf GPL,SL VS 16 Device vendor specific log 0xb0 GPL,SL VS 1 Device vendor specific log 0xb1-0xb5 GPL,SL VS 16 Device vendor specific log 0xb6 SL VS 16 Device vendor specific log 0xb7 GPL,SL VS 40 Device vendor specific log 0xb8-0xbf GPL,SL VS 16 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xde GPL VS 5502 Device vendor specific log 0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 14 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 14 [13] occurred at disk power-on lifetime: 63054 hours (2627 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 01 00 00 00 09 61 e5 90 40 00 Error: UNC at LBA = 0x0961e590 = 157410704 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 09 61 e5 80 40 00 3d+01:07:56.103 READ FPDMA QUEUED 60 01 00 00 00 00 00 09 61 e4 80 40 00 3d+01:07:56.103 READ FPDMA QUEUED 60 01 00 00 00 00 00 09 61 e3 80 40 00 3d+01:07:56.093 READ FPDMA QUEUED 60 00 10 00 00 00 00 00 87 49 50 40 00 3d+01:07:56.093 READ FPDMA QUEUED 60 01 00 00 00 00 00 00 87 48 50 40 00 3d+01:07:56.086 READ FPDMA QUEUED Error 13 [12] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 28 00 01 b9 98 da 30 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 12 [11] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 02 c8 00 01 b9 98 c3 e8 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 11 [10] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 02 40 00 01 b9 98 cf 08 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 10 [9] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 01 f0 00 01 b9 98 b8 d0 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 9 [8] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 41 03 d8 00 01 b9 98 ad b0 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 8 [7] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 02 10 00 01 b9 98 97 78 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 7 [6] occurred at disk power-on lifetime: 63053 hours (2627 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 04 00 00 01 b9 98 8c 58 40 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 63194 - # 2 Extended offline Completed: read failure 90% 63053 157410704 # 3 Short offline Completed without error 00% 63053 - # 4 Extended offline Aborted by host 90% 55628 - # 5 Short offline Completed without error 00% 55628 - # 6 Short offline Completed without error 00% 55627 - 1 of 1 failed self-tests are outdated by newer successful extended offline self-test # 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 27/42 Celsius Lifetime Min/Max Temperature: 16/56 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (387) Index Estimated Time Temperature Celsius 388 2023-12-10 04:59 40 ********************* ... ..( 98 skipped). .. ********************* 9 2023-12-10 06:38 40 ********************* 10 2023-12-10 06:39 41 ********************** ... ..( 84 skipped). .. ********************** 95 2023-12-10 08:04 41 ********************** 96 2023-12-10 08:05 40 ********************* ... ..(156 skipped). .. ********************* 253 2023-12-10 10:42 40 ********************* 254 2023-12-10 10:43 41 ********************** ... ..( 94 skipped). .. ********************** 349 2023-12-10 12:18 41 ********************** 350 2023-12-10 12:19 40 ********************* ... ..( 15 skipped). .. ********************* 366 2023-12-10 12:35 40 ********************* 367 2023-12-10 12:36 39 ******************** ... ..( 19 skipped). .. ******************** 387 2023-12-10 12:56 39 ******************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 74 -D- Lifetime Power-On Resets 0x01 0x010 4 63195 -D- Power-on Hours 0x01 0x018 6 526345016451 -D- Logical Sectors Written 0x01 0x020 6 3628492950 -D- Number of Write Commands 0x01 0x028 6 1671272473177 -D- Logical Sectors Read 0x01 0x030 6 9890453281 -D- Number of Read Commands 0x01 0x038 6 4163700608 -D- Date and Time TimeStamp 0x01 0x048 2 12502 ND- Workload Utilization 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 63195 -D- Spindle Motor Power-on Hours 0x03 0x010 4 53563 -D- Head Flying Hours 0x03 0x018 4 14515 -D- Head Load Events 0x03 0x020 4 200 ND- Number of Reallocated Logical Sectors 0x03 0x028 4 867 -D- Read Recovery Attempts 0x03 0x030 4 0 -D- Number of Mechanical Start Failures 0x03 0x038 4 0 -D- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 54 -D- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 10 -D- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 -D- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 39 -D- Current Temperature 0x05 0x010 1 40 -D- Average Short Term Temperature 0x05 0x018 1 39 -D- Average Long Term Temperature 0x05 0x020 1 56 -D- Highest Temperature 0x05 0x028 1 17 -D- Lowest Temperature 0x05 0x030 1 53 -D- Highest Average Short Term Temperature 0x05 0x038 1 25 -D- Lowest Average Short Term Temperature 0x05 0x040 1 45 -D- Highest Average Long Term Temperature 0x05 0x048 1 34 -D- Lowest Average Long Term Temperature 0x05 0x050 4 0 -D- Time in Over-Temperature 0x05 0x058 1 60 -D- Specified Maximum Operating Temperature 0x05 0x060 4 0 -D- Time in Under-Temperature 0x05 0x068 1 0 -D- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 41 -D- Number of Hardware Resets 0x06 0x010 4 41 -D- Number of ASR Events 0x06 0x018 4 0 -D- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 0 Vendor specific Quote Link to comment
JorgeB Posted December 11, 2023 Share Posted December 11, 2023 You can give it a 2nd chance, any more errors I would replace it. 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.