I'm getting continuous errors in the log during rebuild. I found that my shares were missing so I rebooted. When it came back online the shares were there but warned that files may be unprotected. I looked at the disks next and I had one parity and one array disk in error. So I stopped the array then started without the disks and repeated adding the disks back again.

 I am now getting this continuously in the logs:

 

{Feb  7 09:19:32 Kraken kernel: pcieport 0000:00:01.0: AER: Corrected error message received from 0000:01:00.0
Feb  7 09:19:32 Kraken kernel: pcieport 0000:01:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
Feb  7 09:19:32 Kraken kernel: pcieport 0000:01:00.0:   device [10b5:8724] error status/mask=00000001/0000a000}

I don't know what the error is. Also the array seems to be running the parity okay. What should I do?

 

 Thanks in advance for any help that you can provide.

 

kraken-diagnostics-20250207-0847.zip

Sorry I was not sure if you need this.

 

Model:Custom

M/B:ASUSTeK COMPUTER INC. PRIME Z690-P WIFI Version Rev 1.xx s/n 221213829800159

BIOS:American Megatrends Inc. Version 3601 Dated 10/14/2024

CPU:12th Gen Intel® Core™ i7-12700K @ 4900 MHz

HVM:Enabled

IOMMU:Enabled

Cache:L1 Cache: 384 KiB, L1 Cache: 256 KiB, L2 Cache: 10 MiB, L3 Cache: 25 MiB, L1 Cache: 128 KiB, L1 Cache: 256 KiB, L2 Cache: 2 MiB, L3 Cache: 25 MiB

Memory:96 GiB DDR5 (max. installable capacity 256 GiB)

Network:eth0: 10000 Mbps, full duplex, mtu 1500

Kernel:Linux 6.6.68-Unraid x86_64

OpenSSL:3.4.0

Uptime:7 hours, 42 minutes

Try this first:

 

https://forums.unraid.net/topic/118286-nvme-drives-throwing-errors-filling-logs-instantly-how-to-resolve/?do=findComment&comment=1165009

 

56 minutes ago, JorgeB said:

Try this first:

 

https://forums.unraid.net/topic/118286-nvme-drives-throwing-errors-filling-logs-instantly-how-to-resolve/?do=findComment&comment=1165009

 

Thanks and I  will give it a try.  Will it damage anything to let my parity rebuild finish? I just hate to start over. I would be on edge until it finished.

Should be OK.

1 hour ago, JorgeB said:

Try this first:

 

https://forums.unraid.net/topic/118286-nvme-drives-throwing-errors-filling-logs-instantly-how-to-resolve/?do=findComment&comment=1165009

 

 

Just now, JorgeB said:

Should be OK.

I have never messed with the config file. So do I just go to the  unraid.config and add this at the bottom to it's on line.

Again Thanks

59 minutes ago, ctsdad said:

have never messed with the config file. So do I just go to the  unraid.config and add this at the bottom to it's on line.

You add it to the ‘append’ line for the boot options you want.   Options on the append line are space separated.

Hi sorry for the break in time (Health reasons)

After my parity rebuild I followed the instructions from the listed page and the two above moderators and added " pcie_aspm=off" 

to the green append section as seen in the attached photo. Rebooted and the issue was solved.

 

Thanks to all involved