Hi,
I'm at Unraid 7.0.1 and I still have the problem. My solution for the moment: When the message is popping up during start up, I have to disconnect and reconnect the USB-Drive during the 30 seconds. It is a "workaround" but not a good one. As i see in during startUp: It loads all USB-Devices but the stick as last one and than the stick can't be found anymore. I already thought, maybe my stick is dying and changed it, but that didn't help. Also to put it in some other USB-Interfaces didn't help.

 

For disks: I have 6 HDD Disks, 2 m.2 and 2 SATA-SSD. So 10 disks in sum.

 

I'm a private user and my Mainboard is an Asrock with Intel. With Unraid 6 it worked without any problems.

 

Hope the devs can fix this with Unraid 7.0.2.

 

Edit: my lusb

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 174c:2074 ASMedia Technology Inc. ASM1074 High-Speed hub
Bus 001 Device 003: ID 046d:c24d Logitech, Inc. G710 Gaming Keyboard
Bus 001 Device 004: ID 051d:0002 American Power Conversion Uninterruptible Power Supply
Bus 001 Device 006: ID 346d:5678 6989 Intenso Ultra Line
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 002: ID 174c:3074 ASMedia Technology Inc. ASM1074 SuperSpeed hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub

 

 

Edit: Screenshot from booting. It seems it is ejecting the usb-device: sd 0:0:0:0: [sda] Media removed, stopped polling

Edited March 21, 20251 yr by sognix
add lusb output; add screenshot of booting

1 hour ago, sognix said:

So 10 disks in sum.

If there are only 10 devices it suggests it's not the same issue, post a screenshot of the screen after it stops.

5 hours ago, sognix said:

I'm at Unraid 7.0.1 and I still have the problem.

You could try the 7.1 beta which has raised the limit to 16 devices (it was 8 ) so the flash drive being seen last should then work for you.

18 minutes ago, itimpi said:

You could try the 7.1 beta which has raised the limit to 16 devices (it was 8 )

That limit was also raised for 7.0.1, just 7.0.0 is limited to 8.

Hi, thx for the replys. 

I editet my post with a screenshot of the booting and also, because it was mentionend, after a boot up with the workaround, my lusb.

 

Edited March 22, 20251 yr by sognix

8 hours ago, sognix said:

I editet my post with a screenshot of the booting and also, because it was mentionend, after a boot up with the workaround, my lusb.

The flash drive is being detected as sda, the 1st device, so unrelated to the issue being discussed on this thread:

 

 

Please post the output from 

 

lsub -vt

 

Hi,

lsusb -vt:

 

I also have installed the USB-Manager Plugin, if this gonna help:

 

Thx!

 

Not seeing the flash drive on lsusb, or is this it?

 

During the lsusb the Unraid USB-Drive was the only active drive which was attached via USB. So yes, it has to be that one. It es an Intensio 32 GB USB 3.0 Stick, just 2 weeks old. The Stick before was also an Intensio and worked very well with Unraid 6. Changing to Unraid 7 the problems began, with the old one (as I already said, I thought maybe the stick was dying so I changed) and with the new one.

 

You can also see it on the 2nd screenshot in Port 1-4, which should be in lsusb Bus 001 Port 004.

 

If it helps, it is following Mainboard:

https://pg.asrock.com/mb/Intel/B760M PG Lightning/index.asp

 

The Stick is in this port:

In the neighbouring port is the Keyboard, the USB-C and neighbour are free and in the USB 3.0 ports next to the LAN are a turned off external USB-Drive, and the USB-Connection to my UPS. I also tried the other ports, but it's the same.

Try booting with a different flash drive, no key needed, then post the lsusb -vt output from that, P.S. going to move this all to a new thread, since it's not related to this issue.

Thx for moving the thread.

Used a very old stick (transcend), it bootet normally. lsusb -vt output:

 

 

The old stick which worked with Unraid 6 was also an Intensio.

Edited March 23, 20251 yr by sognix

Strange that it still doesn't show the flash drive brand/model, but now try the old stick with your config folder, there will be a key error, but just see if it still boots normally

It is booting normally with the old Transcend stick and my config. Now I see the GUID-Mismatch as you mentioned. I think it has something to do with the stick, but still: Why was it working with Unraid 6?

 

Also: what do you think, should I do now? I have transfered the license to the new stick und licence transferring is only possible once in 12 months... Or do you think the devs are able to fix it with a following version?

 

Thx for the support!

15 hours ago, sognix said:

what do you think, should I do now?

Transfer the license to a new flash drive, if you cannot do it yourself, contact support.

Hi,

I bought a new stick, an Transcend. With the help of the support I was able to transfer my licence. So a big thank you for your help!