Recently replaced several drives that had problems. Put in last of new drive did 3 pre clears on it and passed each one just fine...now after my first parity check with the newest drive i get 173 errors...log attached thanks

syslog-2012-08-28.zip

Which SATA cards?

no cards just straight from the asrock board

Perform an overnight memtest. Then post SMART reports.

Perform an overnight memtest. Then post SMART reports.

 

im sure this is a stupid question but i have to run a smart scan after the memtest to obtain the results correct?

 

wait...how to i obtain smart results thats not for a specific hard drive?

You do not have to wait until after memtest. But it is good to test the ram as it could very well be the cause.

 

And he meant post smart reports of all of the drives

You do not have to wait until after memtest. But it is good to test the ram as it could very well be the cause.

 

And he meant post smart reports of all of the drives

 

thanks im running memtest now ill let it go for a solid 24 hours. Do i need to run a smart test on each drive then obtain the results individually or is there a way to run it for all of them at once? Also is a short test sufficient enough or should i run long? sorry for dumb questions..thanks again

http://lime-technology.com/wiki/index.php/Troubleshooting#Obtaining_a_SMART_report

http://lime-technology.com/wiki/index.php/Troubleshooting#Obtaining_a_SMART_report

 

i got that i know how to obtain the smart results but my question is that is there a way to do them all at once or is it just one for each disk?  ive looked through the troubleshooting several times and unless i keep over looking it i dont see that option there and if its not there im sure its not possible, just double checking..

 

also before i obtain smart results i must run a smart test correct? if so is the short test good enough or should i do a long test for each disk? thanks again

http://lime-technology.com/wiki/index.php/Troubleshooting#Obtaining_a_SMART_report

 

i got that i know how to obtain the smart results but my question is that is there a way to do them all at once or is it just one for each disk?  ive looked through the troubleshooting several times and unless i keep over looking it i dont see that option there and if its not there im sure its not possible, just double checking..

 

also before i obtain smart results i must run a smart test correct? if so is the short test good enough or should i do a long test for each disk? thanks again

 

Incorrect. Please follow the instructions in the wiki.

http://lime-technology.com/wiki/index.php/Troubleshooting#Obtaining_a_SMART_report

 

i got that i know how to obtain the smart results but my question is that is there a way to do them all at once or is it just one for each disk?  ive looked through the troubleshooting several times and unless i keep over looking it i dont see that option there and if its not there im sure its not possible, just double checking..

 

also before i obtain smart results i must run a smart test correct? if so is the short test good enough or should i do a long test for each disk? thanks again

 

Incorrect. Please follow the instructions in the wiki.

 

ok well since not mentioned in wiki ill assume running a test for the entire array at once isnt an option...i ran memtest just 24 hours went through 24 passes with 0 errors...i have attached a smart results for each drive.

 

i attached a new syslog too

Smart.zip

syslog.zip

Post a syslog after completing a parity check.

Post a syslog after completing a parity check.

 

here is new syslog after parity check. still 173 errors showing...thanks again!

syslog.zip

Where these parity check correcting checks?

yeah i had the correct option check marked

This will take some effort to resolve. See these for ideas:

 

http://lime-technology.com/forum/index.php?topic=19936.0

http://lime-technology.com/forum/index.php?topic=21052.0

http://lime-technology.com/wiki/index.php/FAQ#How_To_Troubleshoot_Recurring_Parity_Errors

man ive just went through a long process and replaced several drives )= lol ill check them out thanks!

i want to try whats in that last link about "How To Troubleshoot Recurring Parity Errors" but i dont know how to build a script? any pointers?

There are scripts in the other threads.

i had some extra g.skill sniper ram laying around i just decided to swap that out and ran parity check no errors...will continue to monitor it...thanks