Mkultra

Thanks for the help guys, Im swapping out a motherboard/cpu on this machine next week so i may just wait until thats done! Maybe rc3 will be ready to put through its paces by then anyway

this is what i get on 6.8 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.19.107-Unraid] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 100 100 000 Pre-fail Always - 0 5 Reallocate_NAND_Blk_Cnt 0x0032 100 100 010 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 4314 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 15 171 Program_Fail_Count 0x0032 100 100 000 Old_age Always - 0 172 Erase_Fail_Count 0x0032 100 100 000 Old_age Always - 0 173 Ave_Block-Erase_Count 0x0032 093 093 000 Old_age Always - 106 174 Unexpect_Power_Loss_Ct 0x0032 100 100 000 Old_age Always - 4 180 Unused_Reserve_NAND_Blk 0x0033 000 000 000 Pre-fail Always - 43 183 SATA_Interfac_Downshift 0x0032 100 100 000 Old_age Always - 0 184 Error_Correction_Count 0x0032 100 100 000 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 194 Temperature_Celsius 0x0022 067 038 000 Old_age Always - 33 (Min/Max 0/62) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Bogus_Current_Pend_Sect 0x0032 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 0 202 Percent_Lifetime_Remain 0x0030 093 093 001 Old_age Offline - 7 206 Write_Error_Rate 0x000e 100 100 000 Old_age Always - 0 210 Success_RAIN_Recov_Cnt 0x0032 100 100 000 Old_age Always - 0 246 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 26188475856 247 Host_Program_Page_Count 0x0032 100 100 000 Old_age Always - 433658808 248 FTL_Program_Page_Count 0x0032 100 100 000 Old_age Always - 599037965

yes it looks like that on 6.8 however on 6.9 ther terminal gave me short 3 line response telling me Smart status is enabled

Yes im am getting temps on 6.8. I have restored back to 6.8 now and unfortunately didnt note it down however it was a short 3 line response telling me my smart is enabled... however as i said not what i expected. This gui also showed this in disk settings: SMART support:Available - device has SMART capability. SMART support:Disabled

SATA controller: Intel Corporation 7 Series/C210 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)

Unfortunately im not at home at the moment. Im running openvpn though, is there any way of checking this on the unraid GUI?

If it helps my four array hdd's are also plugged directly into the sata ports on the motherboard. I have no LSI expansion card etc installed on this machine.

Sata SSD connected straight to the motherboard

IN RC1 i couldnt see the hdd temps no matter what i tried... in RC2 i can see array temps if i spin down then spin up the drives. As far as the cache and flash go nothing i tried made the temps show. Could not get smart enabled on the cache.

Tried RC1 and couldnt get any hdd temps.. Tried RC2, now getting hdd temps when spinning up/down the drives on array but can get no temp on either the cache or flash. Cannot get SMART enabled on cache either. restoring to 6.8 for now.

I have the same problem! anyone figured out a way to fix this? I've tried smartctl '-A /dev/sdX' and i get a message back telling me smart status is enabled.. however when i go into the hdd settings it tells me this: SMART support:Available - device has SMART capability. SMART support:Disabled Very confused!

Ok Thankyou! WIll try all of these!

Hi Guys First post here and i wish it could be more positive. Literally trawled these forums for days for help. I've been having extremly slow read and write speeds on my array since moving to unraid(Often below 1MBps). I've run a freenas server in the past but im completely lost as to what my problem is, Cant see what im missing. Im running a 2TB WD Red as parity as well as a identical drive and a 1TB WD black in the array, I also have an ocz SSD which i am using as cache. The server is hooked up directly to the router which supports 1000MB transfer speeds which a CAT6 cable. I've included my diagnostics in the post and below is an iperf test I've run over wifi. Can include a test done over ethernet but its honestly not much better. Literally any help would be appreciated!! Thanks Connecting to host 192.168.1.121, port 5201 [ 4] local 192.168.1.60 port 54527 connected to 192.168.1.121 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.00 sec 730 KBytes 5.95 Mbits/sec [ 4] 1.00-2.00 sec 1.32 MBytes 11.1 Mbits/sec [ 4] 2.00-3.00 sec 197 KBytes 1.62 Mbits/sec [ 4] 3.00-4.00 sec 1.02 MBytes 8.52 Mbits/sec [ 4] 4.00-5.00 sec 0.00 Bytes 0.00 bits/sec [ 4] 5.00-6.00 sec 20.0 KBytes 163 Kbits/sec [ 4] 6.00-7.00 sec 54.2 KBytes 446 Kbits/sec [ 4] 7.00-8.00 sec 551 KBytes 4.51 Mbits/sec [ 4] 8.00-9.00 sec 701 KBytes 5.75 Mbits/sec [ 4] 9.00-10.00 sec 705 KBytes 5.75 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth [ 4] 0.00-10.00 sec 5.23 MBytes 4.38 Mbits/sec sender [ 4] 0.00-10.00 sec 5.14 MBytes 4.31 Mbits/sec receiver Diagnostics.zip