ctsdad

I am sorry for the loss. I am far more familiar than I would want to be. This time of year is the worse time if there is such a thing.

Back on topic my servers data rebuild is at 80 % and 5 hours. Everything is looking good.

Thanks. I obviously can make it out it just requires me to admit to be old and putting on some reading glasses.

Hey have you seen others having the warnings tray go white to where it can't be read? I sorry that it's off topic.

Okay everything looks good as it is data rebuild is running. Right now it's at 235 MB/ sec and hover at 14 Hours. If nothing happens I will lets you know when it completes and marked as completed. I don't have the extra money until Wednesday but I am setting a reminder to send you something then. As I said thank you. Now I am going to take what I have learned and use it fixing similar issues on a backup Unraid system that I started after this one went down.

Thanks. Disk 1 says "File system corruption fixed." Should I run check again to verify? If not I will move on to Drive 2. Assuming that goes the same do I start the array back as normal?

Okay did that on disc 1. and got: "Phase 1 - find and verify superblock... bad primary superblock - bad CRC in superblock !!! attempting to find secondary superblock... .found candidate secondary superblock... verified secondary superblock... would write modified primary superblock Primary superblock would have been modified. Cannot proceed further in no_modify mode. Exiting now. I have the fix button is that Okay to hit?

OK I'm sorry but I went ahead and restarted in maintenance mode for xfs but at the bottom where the check button should be there is no button for check. The is only the sync button. The two drives 1 & 2 both now show xfs (see the screenshot). Should I start the sync and if so should I only rebuild one disk at a time? Again thanks for your help! kraken-syslog-20251204-1445.zip kraken-diagnostics-20251204-0944.zip

It's at 21% running between 100 MB/ sec to 200 MB/ sec. showing 1 day and 2 hours left. Go ahead and stop parity rebuild and do the file system check and repair?

Thank you for the help you provided so far.

I had a break for a bit and got the power cables inspected and tightened up. I also noticed a switch on my power supply that I think is some kind of Eco Switch that I turned off. I'm confused by why disk 1 & 2 say they are "unmountable: wrong or no file system" and it gives me the option to format the two drives just above where it says "Data Rebuild in Progress". So I hope they are okay and are rebuilding. I am going to add the screenshots of the main page. kraken-diagnostics-20251203-2340.zip kraken-syslog-20251204-0442.zip

I am going to work on this when I can. My wife's,father fell from a scaffolding a while back and is now a quadriplegic. My wife got a call earlier from the doctor wanting to meet with the family and it's not good. I just wanted to let you know that I am grateful for the help and will work on your suggestion as I can . I didn't want you to think that you provided the help and I blew you off afterwards.

I will do that now should I restart and try again? As far as rebuilding?

I am sorry about that I thought I did. kraken-diagnostics-20251203-0937.7z syslog.7z

I had a perfectly ruing system but I had a fan go bad and was making noise so I went to replace it and when I got it back up and running it seemed fine but then later two drives showed up as missing. I went through yesterday and reseated every PCIe device unplugged every cable and made sure to that where replugged tightly at all connections. Turned it back on and everything looked great as I started rebuilding one of the two missing drives. When I went to bed last night it looked great and was rebuilding the drive with ~ 10 hours left. When I checked on it this morning the two parity drives are spun down with errors and one array drive is spun down with errors. The drive being rebuilt was still going and being rebuilt but at ~ 6 MB/s. I am really lost now and I'm not sure what to do or steps to take. I will attach all the system logs, diagnostics, and screenshots. I am going to stop the array. Thanks in advance for any help, Chris

Forgive my rudeness I forgot to say thank you.

Sorry I forgot to add screenshots.

My number 1 disk is full. First is it okay just to leave it? Second after reading a bit here I changed the minimum free space for each disk in the share setting under my data share settings. I set it to something like 500 GB from 98 GB. The drive as it is shows 28.7 KB and. Did I do the correct thing and if so how do I get the system to start spreading the data out to the other drives? All my shares except for ones that stay on ssd drives are set to use all disks. Any help is greatly appreciated. If there is any info needed please let me know.

Hi sorry for the break in time (Health reasons) After my parity rebuild I followed the instructions from the listed page and the two above moderators and added " pcie_aspm=off" to the green append section as seen in the attached photo. Rebooted and the issue was solved. Thanks to all involved

I have never messed with the config file. So do I just go to the unraid.config and add this at the bottom to it's on line. Again Thanks

Thanks and I will give it a try. Will it damage anything to let my parity rebuild finish? I just hate to start over. I would be on edge until it finished.

Sorry I was not sure if you need this. Model:Custom M/B:ASUSTeK COMPUTER INC. PRIME Z690-P WIFI Version Rev 1.xx s/n 221213829800159 BIOS:American Megatrends Inc. Version 3601 Dated 10/14/2024 CPU:12th Gen Intel® Core™ i7-12700K @ 4900 MHz HVM:Enabled IOMMU:Enabled Cache:L1 Cache: 384 KiB, L1 Cache: 256 KiB, L2 Cache: 10 MiB, L3 Cache: 25 MiB, L1 Cache: 128 KiB, L1 Cache: 256 KiB, L2 Cache: 2 MiB, L3 Cache: 25 MiB Memory:96 GiB DDR5 (max. installable capacity 256 GiB) Network:eth0: 10000 Mbps, full duplex, mtu 1500 Kernel:Linux 6.6.68-Unraid x86_64 OpenSSL:3.4.0 Uptime:7 hours, 42 minutes