ChristianMingle

Basically one drive disabled itself a few days ago, and now the second one has disabled itself today. Both of my parity drives are down and i have tried swapping power and data cables separately and neither fixed the problem. Can anyone tell me what the diagnostic data says? Do i need to buy 2 new drives or should i just try to rebuild parity? tower-diagnostics-20230418-2042.zip

I am unable to go to the Apps page, I cannot tunnel in using Wireguard, and i have an "Unraid API error- network error" from the MyServers Plugin. Im not sure whats causing it, i have tried restarting it multiple times, and the problem seems to have arisen out of nowhere. I can still access the server shares from my home network, but it seems like its unable to communicate with anything outside my home network. I have my router port forwarded for everything, and it used to all work fine. Not sure whats causing the sudden problems. I have attached the diagnostics, so if anyone can figure out why this is happening, it would be appreciated. Thank you tower-diagnostics-20230315-1508.zip

?????? as soon as i logged into root and did the diagnostics i can now connect via 192.168.1.151 even though i tried it like 150 times over the past 2 hours. what is going on lol

tower-diagnostics-20220809-1519.zip

OK so apparently the other USB 2.0 is broken, it always gives me a 169 address... i moved it back to the other one and now have a 192 address but back to square 1 where i cannot connect via tower/ or 192.168.1.151

i shut down and removed the usb, ran chkdsk on it, and then put it into a new usb 2.0 slot, and now upon boot it is assigning a 169 adress, which if i recall means that it couldnt get assigned an address. What should i do to fix this?

Mark as Solution yes, same result

I can connect to the server via SSH(filezilla) and i have the monitor showing me the IPv4 Address, its set to what it is normally set to (192.168.1.151) but i cannot connect to the server by typing "tower/" in the url search bar. It just times out and says theres a connection error. I have tried restarting the server, my pc, and the router. Im not sure how to fix it.

a lot of the values are also over the threshhold(provided more info on the middle drive) also i know the F80 has over 55,000 powered on hours on it, its over 6 years old, but everyone always says that they "last forever" so im hoping that this one isnt dying out yet lol

I have a sun F80 drive that i bought used that has 60k hours on it with 117 reallocated sectors on all 4 of the 200GB drives ... im trying to use it and see what happens but im not putting anything valuable on it .. just curious how long itll last lol

also sorry, but can you explain how one of these can be healthy and the other 3 have errors, even though they're all the same drive? I know its actually 4 200GB drives but like, is it just like firmware problems? I find it hard to believe that the one drive i made cache just happened to be the only healthy drive and the other 3 are crapping out lol. (Cache and drive 5,6,7 are all the same Sun Flash Accelerator F80 in case you didnt see the other post yet)

ideally i could make the cache and disks 5,6,7 combine into the 800GB cache disk i originally planned on having. (cache and Disks 5,6, and 7 are all the same Sun Flash Accelerator F80, but i didn't know how to flash it into one 800GB drive) If the cache drive goes offline is it less problematic than other ones? If not should i make the SSD the cache drive and just remove the Sun Flash Accelerator F80? I wish i didn't have to since i overpaid for it to begin with and now its causing problems lol

Last check completed on Sat 06 Aug 2022 05:11:45 AM PDT (yesterday) Finding 48827869 errors Duration: 17 hours, 37 minutes, 51 seconds. Average speed: 154.4 MB/sec diagnostics attached i havent done any of the recommended steps yet as i just got back home, but i figured id post these here because they ran over the time i was gone tower-diagnostics-20220807-2224.zip

also, is it fair to assume that the 3 drives with 50mil errors are probably not in working order? I got the 4x200GB (one device) used and it has had Errors ever since i started using it, but i havent noticed anything but i also try not to use it very much, its HEAVILY used by the last person with something like 60k hours on it, but it is a Sun Oracle F80 800GB so its meant to have a pretty heavily used lifecycle but the errors concern me as every other drive i have is at 0. I think the errors are just bad sectors and i was told that it knows that and avoids using the bad sectors, but dont know more than that.

9.8 TB Elapsed time:less than a minute Current position:4.89 GB (0.0 %) Estimated speed:168.5 MB/sec Estimated finish:16 hours, 8 minutes Sync errors corrected:1193109 im assuming 1mil+ errors within the first 30 seconds of the parity check is not what we are looking for... so i will try updating the SAS firmware later and keep it spun down until i get the chance