tDames

I used Spaceinvaders tutorial before tailscale was integrated into unraid to get swag on my tailscale separated from my NGINXProxymanager because I wanted anything i configured in SWAG to be behind tailscale and NPM to be public. If there is an easier way to do it, I can switch it around. I tried the new config and it still gives me the same error. i almost want to reinstall swag as a whole since I used the old method

Hi, I'm having issues with SWAG communicating outside of my server. I have it set as a serve and have the use tailscale option selected. The errors I've getting are these below. How can i fix this? nginx: [emerg] bind() to 0.0.0.0:443 failed (98: Address in use) nginx: [emerg] bind() to [::]:443 failed (98: Address in use) nginx: [emerg] bind() to 0.0.0.0:443 failed (98: Address in use) nginx: [emerg] bind() to [::]:443 failed (98: Address in use) nginx: [emerg] bind() to 0.0.0.0:443 failed (98: Address in use) nginx: [emerg] bind() to [::]:443 failed (98: Address in use) nginx: [emerg] bind() to 0.0.0.0:443 failed (98: Address in use) nginx: [emerg] bind() to [::]:443 failed (98: Address in use) nginx: [emerg] still could not bind()

Nevermind

I'm using Immich from the community and I'm having an issue with lockup. I've tried to configure things different to defer it and even isolating 4 cores of my 16. It still locks up. Im running a Ryzen 1700 w/ 64GB of ram. Its only when I try to import my library or for it to do it's tasks. Can someone take a look at my log and see if you can spot the issue? ryzennas-diagnostics-20240714-1657.zip

Hi, I'm having issues with my PC locking up for some reason anytime I have a decent sized library. I can't track down the reasoning because I have a capable computer. I've attached a diag file below. I've also restricted it to only use 8 of the 16 cores and watched the activity. It maxes out those cores but the other cores average around 25-35% ryzennas-diagnostics-20240117-0233.zip

I have the ASUS PRIME B450M-A II and I had the 2nd before last update to the bios before. Luckily, they don't push out old code as far as I can tell and I Disabled C-state and also Power Supply Idle Control is set to Typical Current Idle

I have a Ryzen 1700 setup with 2 sticks of 32GB of ram and after the upgrade it's starting to lock up so I upgraded my bios and did a test on the ram to make sure it was stable. I ran the memtest for over 12 hours and it passed all the tests without a xmp profile. I attached the diag files. I hope someone can give me some insight ryzennas-diagnostics-20230502-1507.zip

It doesn't have any power saving properties as far as I could see, but I did run through the bios and disable things that could possibly cause a conflict. Its a change my GPU could be bad also because I noticed it would blank out from bios as I was using it. I'm going to try it in its current configuration right now because Unraid sees the card for now. I'll give it a 24 hours and if it doesn't work, I'll go with one of my older cards.

That's odd. That was after the issue but here's another diag of the same issue of the plugin not finding the GPU also I did switch over to CSM now as of this diag. ryzennas-diagnostics-20220730-0101 - no card found.zip

I'm having a issue. I have a EVGA 1060 6GB and installed the plugin as per instructions and it shows up for some time and then just disappears for no reason. Here is my Diag zip ryzennas-diagnostics-20220728-1728 after nvidia.zip