ItsRaining

Members
  • Posts

    35
  • Joined

  • Last visited

Everything posted by ItsRaining

  1. Yes that Is how I downloaded the backup shown above. If you see picture above I cannot get my Unraid server to post at all now. I tried using the following settings and putting my pro.key file inside the config folder: However I just get the blank post screen you see in my previous post.
  2. No I failed to grab a backup of the flash. Completely my fault, however last time I was having this same issue I grabbed a flash backup and it had the same missing contents of the config folder. Here is my previous backup that also failed. Every time I have pulled my flash drive and looked in it there was no config folder unless I had just run the Unraid creation tool on it.
  3. The flash drive is plugged into a USB 2.0 port. Here is the contents of the flash drive. Seems a little lacking: Here is the results of the chkdsk: After plugging it in to a new USB2 slot I do not get past a blank post screen. I do not mind remaking my dockers at all if this problem does not persist. I tried using the Unraid tool to make a new flash drive and place my pro.key in the Config folder. However, I get the same post screen as my previous flash drive.
  4. Bueller. Bueller. Bueller. Really need help. Now my entire docker and Unraid. That error persisted with no changes until now everything is broken and Unraid claims it is unreadable. Really could use help. I have not been able to use Unraid without any errors since purchase and its making question why I didn't just use windows.
  5. I have been having an issue with my Unraid receiving this error on my Dashboard. Originally thought it was a bad flash drive but after changing to a new one the error has returned. I have attached my diagnostics for review. Thank you in advanced for any assistance. tower-diagnostics-20210824-1935.zip
  6. All the config folders are there. I am just reinstalling the images and setting the environment variables. So its no big deal.
  7. Thank you for the information to get the registration key to work. I cannot believe I missed such a simple step. I successfully registered my new USB. Using a new install of Unraid seems to have broken all my dockers and VMs but I will gladly remake them. All my data is still available and that is what I care about most. I still am not sure if I have resolved the GUI issue when I restart. I am running a parity check and once finished I will try restarting the server. Hopefully the ipv4 registers.
  8. I have done another fresh install so I can get to the GUI and get the diagnostics. This is not my old zip file. If I try to use my old zip backup I fail to access the GUI. Here is the zip you requested. tower-diagnostics-20210824-0650.zip I see the network working. Maybe its my network settings? I can post those if requested. Also, help replacing my key would be appreciated. Do I need to reach out to Unraid support to get a link? There is no replace key button.
  9. Good morning, I have been wrapping my brain around trying to install my unraid server on a new USB drive. This all started when I received an error on my unraid dashboard (first image). After some research I concluded that the flash drive was faulty. I purchased a Samsung BAR Plus after watching some reviews on which USB to use. Then the headaches started. I first grabbed a flash backup from my running unraid server. I shut it down and using the creation tool ran the ZIP file on my new USB with UEFI enabled. However, when I installed this stick and ran it in Unraid at first it would fail to post only blinking after the motherboard screen. Since restarting and trying again I continue to get a 169 address. I understand it is failing to acquire an address from DHCP. However, when I type ifconfig. The proper IP address shows up under br0 and nothing shows under eth0. Please know that I have many other computers on the network obtaining IP addresses perfectly fine. The server also had the correct IP address before the flash drive change. I have attempted the following: 1. Change out the ethernet cable and ports on both ends. 2. Use a third different flash drive. 3. Use the old flash drive again (just goes to a blinking post screen after the motherboard screen) 4. Use the unraid flash creator with the backup zip file (makes it to the Unraid OS screen with 5 second timer and repeats in a loop fails to boot) 5. Use the Unraid Flash Creator with a fresh Stable release. This loads correctly but gives me a 169 ipv4 address. ifconfig shows the correct 192 address under br0 and I am able to access the UI. However, I cannot successful get my pro.key to install. There is only a Purchase and Trial buttons. I am extremely afraid I just lost all my data if I have to start with a new Unraid OS. The data is on the HDDs, but the array is no longer available with the USB drive issues I am having. I have no idea how or where to pull the systemlogs from the CLI and I see no logs file on the flash drive. Motherboard: Gigabyte X570 Aurous Master CPU: AMD 3600X RAM: Tridentz Royal 3600 mhz