vettenstein

Great, thanks!

GluetunVPn shows to support AirVPN in v3.32 The one that shows up in Apps is v3.31.1 Would it be possible to get the latest version posted? Thanks

That was it. Thanks. I've only been clicking through the settings most of the day and completely missed the 'Disk Settings'.

What has lead to this... My flash drive corrupted during the upgrade from 6.2.1 to 6.2.2. Tried flash drive in my Windows PC and it showed as RAW. Found a flash drive test program and it showed 1k+ errors. Tossed failed flash drive and have clean installed 6.2.2 on new flash drive and fixed the GUID Registration. Current issue is after a Reboot or Shutdown/Start, the Array is not automatically mounting. Shows 'Array Stopped'. I can manually select 'Start' and it will come online. Any ideas? tower-diagnostics-20161023-1354.zip

I'm on 6.2 and there doesn't appear to be a way to 'Start' the array with the swapped assignments. I'm getting... The 'Start' is grayed out and nothing to tick to continue. I'm presuming, it's not necessary to swap assignments, if I'm keeping track of the drives through the migration. WAG, but you can't swap assignments if you have both parity disks enabled and valid. Single parity - switching slots allowed, Dual parity - slots not movable without recalculating Q parity. It's not necessary to swap things around as long as you don't use disk specific locations, and even then it's fine as long as you change the assignments to track the new disk number. Thanks, but I'm only using single Parity. Also don't have User Shares. Unlike v6.1, v6.2 doesn't allow disk swapping even when using single parity, Tom already posted that this will be fixed on a future release. Must have missed that discussion. So, for now if you want to move disk assignments, you will have to set a new config and carefully assign the drives where you want them. Just be ABSOLUTELY positive which drive is your parity drive. You can check the box to indicate parity is already valid, but I would do a parity check afterwards anyway. Unless you have a pressing need to keep each migration's disk assignments correct, I'd just wait til you are all done, then reassign all disks at once. Understood, thanks.

I'm on 6.2 and there doesn't appear to be a way to 'Start' the array with the swapped assignments. I'm getting... The 'Start' is grayed out and nothing to tick to continue. I'm presuming, it's not necessary to swap assignments, if I'm keeping track of the drives through the migration. WAG, but you can't swap assignments if you have both parity disks enabled and valid. Single parity - switching slots allowed, Dual parity - slots not movable without recalculating Q parity. It's not necessary to swap things around as long as you don't use disk specific locations, and even then it's fine as long as you change the assignments to track the new disk number. Thanks, but I'm only using single Parity. Also don't have User Shares. Unlike v6.1, v6.2 doesn't allow disk swapping even when using single parity, Tom already posted that this will be fixed on a future release. Thanks for the clarification. I'll just skip the assignment swapping steps and just use the previous drive as the 'new' empty.

I'm on 6.2 and there doesn't appear to be a way to 'Start' the array with the swapped assignments. I'm getting... The 'Start' is grayed out and nothing to tick to continue. I'm presuming, it's not necessary to swap assignments, if I'm keeping track of the drives through the migration. WAG, but you can't swap assignments if you have both parity disks enabled and valid. Single parity - switching slots allowed, Dual parity - slots not movable without recalculating Q parity. It's not necessary to swap things around as long as you don't use disk specific locations, and even then it's fine as long as you change the assignments to track the new disk number. Thanks, but I'm only using single Parity. Also don't have User Shares.

I'm on 6.2 and there doesn't appear to be a way to 'Start' the array with the swapped assignments. I'm getting... The 'Start' is grayed out and nothing to tick to continue. I'm presuming, it's not necessary to swap assignments, if I'm keeping track of the drives through the migration.

Ok, thanks.

koshia Do you have the 'eye' icon? EDIT: It probably only shows after starting a preclear. I'm curious if it shows only when a preclear is started from the plugin or if it should also be there if a preclear was started manually?

Updated to .26b and still had the same issue. I noticed on the flash, I had a new directory /boot/.preclear I didn't see a directory /boot/preclear_reports - I added the directory manually and it now shows me the unassigned drive. I presume it may be working now. Can't test, as I'd already started the preclear manually. Is this all I will see, if I currently have the preclear running manually? EDIT: I also ran the tmux code and still have... if that matters? EDIT2: I guess something is still wrong, I don't see the 'eye' that was being discussed earlier and in gfjardim's screenshot.

So I ran the update and had the same issue after starting the plugin. Ran what you posted previously. tmux ls|awk 'BEGIN { FS=":" } /^preclear_disk/ {print $1}'|while read i; do tmux capture-pane -t "$i" && tmux show-buffer | sed '/^$/{:a;N;s/\n$//;ta}'; done Did what PhAzE posted... touch /tmp/tmux-0/default re-ran the tmux code Still not able to start the plugin.

I have this issue with 6.2, using the latest Preclear plugin. Installed from CA. Modified the script as suggested. It never shows any drives. I'm able to run the script manually through Screen/Putty without a problem.

How much?

Is this still available or SOLD?