bisk

I updated my server, but after the reboot and when accessing the GUI from my iPad or directly on the server, I’m getting a “File not found” error. If I boot into Safe Mode with GUI, I’m able to access the GUI from my iPad and directly from the server. I’ve attached my Diagnostics file. homeserver-diagnostics-20180901-0837.zip

OK, thanks for the help. Short of removing all of the plugins and re-adding them one-by-one and stopping all of the dockers and starting them one-by-one each day, is there anything else I could do to help ID the troubled one?

Yeah, I remember you mentioning that above, so I had set them back to the defaults, but I continued to receive the Out of Memory errors, so I put them back 1 and 2 a little while ago. There have been many reboots since changing that setting. I usually reboot the server after dinner if I know that we're going to watch Plex that evening since a reboot will restore the server to acceptable performance to use Plex.

So I've since upgraded to v6.4_rc10b and I'm still receiving Out of Memory and Call Traces errors from Fix Common Problems. My monthly Parity check started last night and was running at around 1MB/s when I checked this morning. I've set the cache % back to 1 and 2 to help with the Out of Memory errors, but it would appear that that hasn't helped. Any help in resolving this issue would be greatly appreciated since I'm not able to use Plex and I have some you and female family members that are constantly bugging me homeserver-diagnostics-20171102-0720.zip

I had an email from the Fix Common Problems plug-in this morning stating that I had Call Traces again. I’ve attached my Diagnostics Report. homeserver-diagnostics-20171014-1105.zip

Thanks again. I ran btrfs balance start --full-balance /mnt/cache and it said that it had to relocate 479 out of 479. I've also changed the cache sizes to 1 and 2 as you suggested.

Thanks johnnie.black. I read through the thread and set the cache to 50% of the defaults. I’m still seeing really slow writes to my pool. Downloading with SABnzbd to a drive outside of the pool is fast though. I ran a test with Disk Speedtest plugin and I’ve attached the results from that. All of the drives seem to be running fine, so I’m stumped on why the writing it so slow... Edit - I see that that is just a test of the read speeds only, so I don’t have a view into the write speeds Although my read speeds seem to be an issue too since I’m not able to play anything through Plex anymore either.

Looks like my server was completely hung this morning. I wasn’t able to access any of my Dockers or the Web UI. I’ve attached a picture of the console before a reset it.

I’ve attached my Diagnosis Report. Fix Common Problems is reporting that Call Traces have been found on my server. Any assistance is appreciated. homeserver-diagnostics-20171009-1231.zip I’ve also noticed that copying between drives in my server is super slow. It looks like it’s copying bytes/second at the moment. I’m able to read files off of the server no problem though. Seems to only be an issue writing to the Pool.

So I decided to give it another shot yesterday and I was able to successfully pass the Intel iGPU through to a VM! The weird part is that the only way I could get it to work was to set the iGPU as the default video card in BIOS. This is fine, except once I start the VM I loose Console access on my monitor. This is fine until a time when I loose network access to my UNRAID box and need to use the console instead

Well, I think I figured it out My CPU is the i7 3770, which is an Ivy Bridge CPU and it looks like this processor generation isn't supported (as stated in the Intel IGD Support Thread...boo!

I tried that build with the same result. What I find strange is that I don't even see anything during the boot (no BIOS or POST messages like I see with my other VMs). When the VM starts up, the screen is just the lines and never changes, so it looks like nothing is booting in the background. I noticed the Xeon e3 CPU selection as well and just figured it was what UNRAID detected my CPU as, but it is an i7.

I installed the most resent version from their site; I believe it was 8.0.2. I hooked it up to my monitor via VGA and to my projector via HDMI and both display the same image.

I’m trying to get LibreELEC up and running and passing the Intel GPU through to the VM, but for whatever reason when I power the VM up all I get is the garbelled image that I’ve attached. I also attached a screenshot of the KVM configuration for the VM as well as the information on my Motherboard and CPU. Anyone have any ideas on how I can get this working?

See here: http://lime-technology.com/forum/index.php?topic=40937.msg463355#msg463355 Awesome! That worked. Thanks.

I seem to be having an issue getting this docker installed. After configuring the install through the Community Apps Plugin the install screen displays the following and I see the weird error bolded below...any thoughts? Any other logs I can attach?

If I change my Dockers to use /mnt/cache/ how do back them up? I've got my Dockers running from /mnt/user/AppData so that everything is protected in the Array. It's one of the questions I've had about Dockers and unRAID, but I haven't been able to find a definitive answer.

I did a fresh install of PlexRequests yesterday, but it doesn't appear to be working. The Docker starts, but I'm never able to connect to the Web UI (http://towerip:3000). Any thoughts? Here's the log