Kash76

Advice is appreciated! I have 9,100 read errors on this disk... Thanks! smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.14.35-unRAID] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD30EZRX-00DC0B0 Serial Number: WD-WMC1T1274820 LU WWN Device Id: 5 0014ee 00378dbe0 Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 3 12:04:19 2018 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 119) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: (41520) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 417) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1548 3 Spin_Up_Time POS--K 189 183 021 - 5516 4 Start_Stop_Count -O--CK 100 100 000 - 47 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 085 085 000 - 11531 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 45 192 Power-Off_Retract_Count -O--CK 200 200 000 - 26 193 Load_Cycle_Count -O--CK 100 100 000 - 301196 194 Temperature_Celsius -O---K 125 105 000 - 25 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 4 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 489 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 489 [8] occurred at disk power-on lifetime: 11497 hours (479 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 04 e8 00 00 8e 7e 6d 08 e0 00 Error: UNC 1256 sectors at LBA = 0x8e7e6d08 = 2390650120 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 04 e8 00 00 8e 7e 69 a8 e0 08 05:16:13.186 READ DMA EXT 25 00 00 02 08 00 00 8e 7e 67 a0 e0 08 05:16:13.184 READ DMA EXT 25 00 00 05 10 00 00 8e 7e 62 90 e0 08 05:16:13.178 READ DMA EXT 25 00 00 02 08 00 00 8e 7e 60 88 e0 08 05:16:13.176 READ DMA EXT 25 00 00 04 e8 00 00 8e 7e 5b a0 e0 08 05:16:13.170 READ DMA EXT Error 488 [7] occurred at disk power-on lifetime: 11497 hours (479 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 05 40 00 00 8d f3 13 a8 e0 00 Error: UNC 1344 sectors at LBA = 0x8df313a8 = 2381517736 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 05 40 00 00 8d f3 0f f8 e0 08 05:15:23.435 READ DMA EXT 25 00 00 02 80 00 00 8d f3 0d 78 e0 08 05:15:23.431 READ DMA EXT 25 00 00 02 e0 00 00 8d f3 0a 98 e0 08 05:15:23.429 READ DMA EXT 25 00 00 02 08 00 00 8d f3 08 90 e0 08 05:15:23.427 READ DMA EXT 25 00 00 01 68 00 00 8d f3 07 28 e0 08 05:15:23.425 READ DMA EXT Error 487 [6] occurred at disk power-on lifetime: 11497 hours (479 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 02 08 00 00 8d 65 54 b0 e0 00 Error: UNC 520 sectors at LBA = 0x8d6554b0 = 2372228272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 02 08 00 00 8d 65 54 28 e0 08 05:14:29.735 READ DMA EXT 25 00 00 04 d8 00 00 8d 65 4f 50 e0 08 05:14:29.731 READ DMA EXT 25 00 00 02 08 00 00 8d 65 4d 48 e0 08 05:14:29.719 READ DMA EXT 25 00 00 05 20 00 00 8d 65 48 28 e0 08 05:14:28.757 READ DMA EXT 25 00 00 02 08 00 00 8d 65 46 20 e0 08 05:14:28.755 READ DMA EXT Error 486 [5] occurred at disk power-on lifetime: 11497 hours (479 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 05 40 00 00 8d 3f f7 68 e0 00 Error: UNC 1344 sectors at LBA = 0x8d3ff768 = 2369779560 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 05 40 00 00 8d 3f f4 e8 e0 08 05:14:05.349 READ DMA EXT 25 00 00 02 10 00 00 8d 3f f2 d8 e0 08 05:14:05.337 READ DMA EXT 25 00 00 05 40 00 00 8d 3f ed 98 e0 08 05:14:05.275 READ DMA EXT 25 00 00 01 b0 00 00 8d 3f eb e8 e0 08 05:14:05.209 READ DMA EXT 25 00 00 05 40 00 00 8d 3f e6 a8 e0 08 05:14:05.155 READ DMA EXT Error 485 [4] occurred at disk power-on lifetime: 11497 hours (479 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 05 40 00 00 8d 3f cd b8 e0 00 Error: UNC 1344 sectors at LBA = 0x8d3fcdb8 = 2369768888 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 05 40 00 00 8d 3f c8 88 e0 08 05:13:57.365 READ DMA EXT 25 00 00 02 58 00 00 8d 3f c6 30 e0 08 05:13:57.363 READ DMA EXT 25 00 00 05 40 00 00 8d 3f c0 f0 e0 08 05:13:57.305 READ DMA EXT 35 00 00 01 60 00 00 8d 3f b8 c0 e0 08 05:13:57.300 WRITE DMA EXT 25 00 00 04 c8 00 00 8d 3f bc 28 e0 08 05:13:57.286 READ DMA EXT Error 484 [3] occurred at disk power-on lifetime: 11497 hours (479 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 05 30 00 00 8d 3f b8 c0 e0 00 Error: UNC 1328 sectors at LBA = 0x8d3fb8c0 = 2369763520 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 05 30 00 00 8d 3f b4 f0 e0 08 05:13:54.314 READ DMA EXT 25 00 00 02 08 00 00 8d 3f b2 e8 e0 08 05:13:54.312 READ DMA EXT 25 00 00 01 70 00 00 8d 3f b1 78 e0 08 05:13:54.311 READ DMA EXT 25 00 00 05 40 00 00 8d 3f ac 38 e0 08 05:13:54.305 READ DMA EXT 25 00 00 00 10 00 00 8d 3f ac 28 e0 08 05:13:54.305 READ DMA EXT Error 483 [2] occurred at disk power-on lifetime: 11497 hours (479 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 02 08 00 00 8d 3e 9a 40 e0 00 Error: UNC 520 sectors at LBA = 0x8d3e9a40 = 2369690176 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 02 08 00 00 8d 3e 98 e0 e0 08 05:13:50.191 READ DMA EXT 25 00 00 02 f8 00 00 8d 3e 95 e8 e0 08 05:13:50.177 READ DMA EXT 25 00 00 02 00 00 00 8d 3e 93 e8 e0 08 05:13:50.176 READ DMA EXT 25 00 00 02 08 00 00 8d 3e 91 e0 e0 08 05:13:50.175 READ DMA EXT 25 00 00 02 80 00 00 8d 3e 8f 60 e0 08 05:13:50.168 READ DMA EXT Error 482 [1] occurred at disk power-on lifetime: 11497 hours (479 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 02 88 00 00 8d 3e 70 48 e0 00 Error: UNC 648 sectors at LBA = 0x8d3e7048 = 2369679432 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 02 88 00 00 8d 3e 6f 38 e0 08 05:13:46.868 READ DMA EXT 25 00 00 02 00 00 00 8d 3e 6d 38 e0 08 05:13:46.867 READ DMA EXT 25 00 00 02 08 00 00 8d 3e 6b 30 e0 08 05:13:46.866 READ DMA EXT 25 00 00 03 70 00 00 8d 3e 67 c0 e0 08 05:13:46.863 READ DMA EXT 25 00 00 02 00 00 00 8d 3e 65 c0 e0 08 05:13:46.862 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 70% 11517 1483616232 # 2 Short offline Completed without error 00% 11515 - # 3 Extended offline Completed without error 00% 1756 - # 4 Short offline Completed without error 00% 1748 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 20/27 Celsius Lifetime Min/Max Temperature: 18/45 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (233) Index Estimated Time Temperature Celsius 234 2018-06-03 04:07 25 ****** ... ..( 20 skipped). .. ****** 255 2018-06-03 04:28 25 ****** 256 2018-06-03 04:29 24 ***** ... ..( 35 skipped). .. ***** 292 2018-06-03 05:05 24 ***** 293 2018-06-03 05:06 25 ****** ... ..( 5 skipped). .. ****** 299 2018-06-03 05:12 25 ****** 300 2018-06-03 05:13 24 ***** ... ..( 2 skipped). .. ***** 303 2018-06-03 05:16 24 ***** 304 2018-06-03 05:17 25 ****** ... ..( 5 skipped). .. ****** 310 2018-06-03 05:23 25 ****** 311 2018-06-03 05:24 24 ***** ... ..( 84 skipped). .. ***** 396 2018-06-03 06:49 24 ***** 397 2018-06-03 06:50 25 ****** ... ..( 5 skipped). .. ****** 403 2018-06-03 06:56 25 ****** 404 2018-06-03 06:57 24 ***** ... ..( 24 skipped). .. ***** 429 2018-06-03 07:22 24 ***** 430 2018-06-03 07:23 25 ****** ... ..( 6 skipped). .. ****** 437 2018-06-03 07:30 25 ****** 438 2018-06-03 07:31 24 ***** ... ..( 4 skipped). .. ***** 443 2018-06-03 07:36 24 ***** 444 2018-06-03 07:37 25 ****** 445 2018-06-03 07:38 24 ***** ... ..( 23 skipped). .. ***** 469 2018-06-03 08:02 24 ***** 470 2018-06-03 08:03 25 ****** 471 2018-06-03 08:04 24 ***** ... ..( 3 skipped). .. ***** 475 2018-06-03 08:08 24 ***** 476 2018-06-03 08:09 25 ****** 477 2018-06-03 08:10 24 ***** 0 2018-06-03 08:11 24 ***** 1 2018-06-03 08:12 24 ***** 2 2018-06-03 08:13 25 ****** 3 2018-06-03 08:14 25 ****** 4 2018-06-03 08:15 24 ***** ... ..( 3 skipped). .. ***** 8 2018-06-03 08:19 24 ***** 9 2018-06-03 08:20 25 ****** ... ..( 5 skipped). .. ****** 15 2018-06-03 08:26 25 ****** 16 2018-06-03 08:27 24 ***** ... ..( 2 skipped). .. ***** 19 2018-06-03 08:30 24 ***** 20 2018-06-03 08:31 25 ****** 21 2018-06-03 08:32 24 ***** 22 2018-06-03 08:33 24 ***** 23 2018-06-03 08:34 25 ****** ... ..( 2 skipped). .. ****** 26 2018-06-03 08:37 25 ****** 27 2018-06-03 08:38 24 ***** ... ..( 2 skipped). .. ***** 30 2018-06-03 08:41 24 ***** 31 2018-06-03 08:42 25 ****** ... ..( 9 skipped). .. ****** 41 2018-06-03 08:52 25 ****** 42 2018-06-03 08:53 24 ***** 43 2018-06-03 08:54 25 ****** ... ..( 9 skipped). .. ****** 53 2018-06-03 09:04 25 ****** 54 2018-06-03 09:05 24 ***** 55 2018-06-03 09:06 24 ***** 56 2018-06-03 09:07 24 ***** 57 2018-06-03 09:08 25 ****** ... ..( 3 skipped). .. ****** 61 2018-06-03 09:12 25 ****** 62 2018-06-03 09:13 24 ***** 63 2018-06-03 09:14 24 ***** 64 2018-06-03 09:15 24 ***** 65 2018-06-03 09:16 25 ****** ... ..( 4 skipped). .. ****** 70 2018-06-03 09:21 25 ****** 71 2018-06-03 09:22 24 ***** 72 2018-06-03 09:23 24 ***** 73 2018-06-03 09:24 25 ****** ... ..( 11 skipped). .. ****** 85 2018-06-03 09:36 25 ****** 86 2018-06-03 09:37 24 ***** 87 2018-06-03 09:38 25 ****** ... ..( 8 skipped). .. ****** 96 2018-06-03 09:47 25 ****** 97 2018-06-03 09:48 24 ***** 98 2018-06-03 09:49 25 ****** ... ..( 7 skipped). .. ****** 106 2018-06-03 09:57 25 ****** 107 2018-06-03 09:58 24 ***** 108 2018-06-03 09:59 24 ***** 109 2018-06-03 10:00 24 ***** 110 2018-06-03 10:01 25 ****** ... ..( 8 skipped). .. ****** 119 2018-06-03 10:10 25 ****** 120 2018-06-03 10:11 24 ***** 121 2018-06-03 10:12 25 ****** ... ..( 7 skipped). .. ****** 129 2018-06-03 10:20 25 ****** 130 2018-06-03 10:21 24 ***** 131 2018-06-03 10:22 24 ***** 132 2018-06-03 10:23 24 ***** 133 2018-06-03 10:24 25 ****** ... ..( 5 skipped). .. ****** 139 2018-06-03 10:30 25 ****** 140 2018-06-03 10:31 24 ***** ... ..( 15 skipped). .. ***** 156 2018-06-03 10:47 24 ***** 157 2018-06-03 10:48 25 ****** 158 2018-06-03 10:49 25 ****** 159 2018-06-03 10:50 25 ****** 160 2018-06-03 10:51 24 ***** ... ..( 14 skipped). .. ***** 175 2018-06-03 11:06 24 ***** 176 2018-06-03 11:07 25 ****** 177 2018-06-03 11:08 25 ****** 178 2018-06-03 11:09 24 ***** 179 2018-06-03 11:10 25 ****** 180 2018-06-03 11:11 25 ****** 181 2018-06-03 11:12 25 ****** 182 2018-06-03 11:13 24 ***** ... ..( 4 skipped). .. ***** 187 2018-06-03 11:18 24 ***** 188 2018-06-03 11:19 25 ****** ... ..( 5 skipped). .. ****** 194 2018-06-03 11:25 25 ****** 195 2018-06-03 11:26 24 ***** ... ..( 2 skipped). .. ***** 198 2018-06-03 11:29 24 ***** 199 2018-06-03 11:30 25 ****** ... ..( 6 skipped). .. ****** 206 2018-06-03 11:37 25 ****** 207 2018-06-03 11:38 24 ***** 208 2018-06-03 11:39 24 ***** 209 2018-06-03 11:40 24 ***** 210 2018-06-03 11:41 25 ****** ... ..( 22 skipped). .. ****** 233 2018-06-03 12:04 25 ****** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 140697 Vendor specific

Manually like CHBMB said.

@opticonThank you very much for sharing this. I've been struggling with the 'external_url' parameter for a while. I did get this working but I intermittently get sent back to my internal IP:port address. Any ideas on how to solve this?

***update - apparently my upgrade did not go well. I copied all of the 12.0.5 files over my existing (the new signer certs were missing completely) and now I'm back in business. I am suddenly getting a "too many redirects" error after login when visiting my instance. I recently upgraded to 12.05 and use LetsEncrypt as a reverse proxy. Any ideas as to what could cause this error? I have the same issue when I disable overwrite.cli.url and overwrite host and access the domain locally without my external LetsEncrypt reverse proxy.

Darn Sent from my ONEPLUS A5010 using Tapatalk

I thought Comcast did as well but I set the port forwarding on 80 and it works for me. Try it. Sent from my ONEPLUS A5010 using Tapatalk

I would also like to thank the great people at Linuxserver.io for all of the goodies that that offer us!!!

Interesting - I ended up forwarding port 80 to 8008 (container http port) and it started working along with HTTPVAL (under Docker, LetsEncrypt, advanced settings to true). I believe that Comcast blocks 80 but it's working.

There does not seem to be a clear path to a fix for those of us with port 80 blocked correct? Sent from my ONEPLUS A5010 using Tapatalk

Thanks. I'll assume the same if I bite on a 512, I'd get half or less because of the increase? Sent from my ONEPLUS A5010 using Tapatalk

Good evening everyone! I have 2 x 275GB Crucial SSD drives for my cache pool and I'm running short on space. I have a 128GB sitting at my desk and am wondering if I can add it to the pool? I assume that I will not get the full 128GB but will it allocate maybe half of that? Thanks for the guidance, I'd rather not have to purchase two new 512GB or larger.

Up and running, thanks!!

Thanks for setting this up! I'll check it out as we are considering this for a Slack alternative at work.

I have. I created my user account as an admin, updated the server, and I don't see a way to delete the admin user. I never can login as my additional user. Not sure what I'm still doing wrong. Sent from my ONEPLUS A5000 using Tapatalk

I am struggling with this container as it seems others are. I have local users created in the docker image by using 'docker exec -it openvpn-as adduser username', I set a password with 'docker exec -it openvpn-as passwd username', add the user as an admin, and I still cannot use any user except for admin. I have also commented out the line 'boot_pam_users'. What am I missing?

I have not had this issue Sent from my ONEPLUS A5000 using Tapatalk

I have added this to extra parameters to help control the sprawl of log files "--log-opt max-size=50m --log-opt max-file=1" Sent from my ONEPLUS A5000 using Tapatalk

Yes, thank you very much Sent from my ONEPLUS A5000 using Tapatalk

Bump

Trying to use a proxy for my connections out and I have found the "--ProxyConnection=10.0.0.xx:xxxx" argument but when I add it to the extra params line the container fails to start. Any ideas?

Perfect. Thanks! Sent from my ONEPLUS A3000 using Tapatalk

That's odd isn't it? How would I keep it upgraded other than updating the docker settings version by version? Sent from my ONEPLUS A3000 using Tapatalk

Hey guys, I want to try out the new live tv feature and I am a PlexPass owner. Can I use this docker to enable the PlexPass release? I've changed the dropdown in the Plex gui and it wants a manual install and I tried "-e VERSION=plexpass" in the parameters section 'stealing' from another docker parameter. What am I missing. Thanks!

Thanks! Sent from my ONEPLUS A3000 using Tapatalk

Any chance that this image will be updated to 2.5? Thanks!