Trebron74

The more than one Server scenario is not clear enough and the Pub.sh pic is no longer available. I would like to run all 3 mods of OpenRA and cannot figure out the dal router portfowarding and server port/listen port/ Ext port combos for this

And it solved it! Thank a lot for the fast help

This is an setting related to an Plugin called TurboMode. Thanks for the hint. Set it long ago due to some GUI Lockups and forgot to disable it again

After updating to V6.5.0 I'm no longer able to update outdated plugins or remove plugins. The popup states that the plugin in is not installed but listed under plugins tab and is running and available (Settings Tab) in my current unRAID system fatmax-diagnostics-20180322-1105.zip

Hello community - I'm seeing my parity disk disabled without any action and no issues (at least from my point of view). I've changed controller and cabling, removed and re-added the drive but it goes to disabled state shortly before parity rebuild completes. Smart does not report errors beside 2 UDMA CRC Errors (that's why I changed the connections)... Any idea what could be wrong? attached are the diagnostics files as needed. fatmax-diagnostics-20180126-1951.zip

I struggle a lot with sporadic unresponsive GUI, but working SSH connections as well as unresponsive GUI and SSH terminal. As I start a new topic with debugging information I would like to prepare a fresh build using my licensed USB key. Debugging information is actually captured but need to wait for the next unresponsive session... Is there a procedure to save important files/settings/license items to be prepared for a fresh build? I assume to be saved: Disk layout (Informational to rebuild using the GUI) License File (copied from /boot/config as file) --> the pro.key file is not visible on the USB key when mounted /flash... Do I miss something? Docker Config (Informational to rebuild using the GUI) KVM XML with manual edits (as Text file for copy and paste) I would start as small and skimmed down as possible to avoid conflicts and perform debugging analysis while enabling apps/plugins, dockers, VM step by step. Initial start would be unRAID + Plex Docker only Searching the forum was not answering my question about the backup steps... Thanks a lot.

Any idea about my error? This is coming from unRAID KVM Manger when I power on the VM. Or better a separate thread? Any idea about my error? This is coming from unRAID KVM Manger when I power on the VM. Or better a separate thread?

I do have similar issues. once I added my original MacPro (late 2009) GeForce GT 120 Gfx card into my unRAID and wanted to pass it trough to my macOS KVM running 10.12.4 Error Message: internal error: process exited while connecting to monitor: 2017-05-09T13:49:59.860781Z qemu-system-x86_64: -device vfio-pci,host=01:00.0,id=hostdev0,bus=pci.2,addr=0x4: vfio: error, group 1 is not viable, please ensure all devices within the iommu_group are bound to their vfio bus driver. 2017-05-09T13:49:59.860801Z qemu-system-x86_64: -device vfio-pci,host=01:00.0,id=hostdev0,bus=pci.2,addr=0x4: vfio: failed to get group 1 2017-05-09T13:49:59.860810Z qemu-system-x86_64: -device vfio-pci,host=01:00.0,id=hostdev0,bus=pci.2,addr=0x4: Device initialization failed and replaced the VNC portion with <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x01' slot='0x00' function='0x0'/> </source> </hostdev> as stated in the guide from gridrunner unRAID seems to have the problem that qemu does not "known" my GT 120. What do I miss?

Thanks a lot for the hint with the 2nd video to get it running with OS X Sierra 10.12.4. As this version is actually used when creating the image in VMware, I missed the UPDATE portion (I was already on.4 so no need to watch But now, with the machine up and running a basic question came up and I was not able to search for an answer. Increase the disk size of the vm. My first (and IMHO logical) step was to define a bigger disk in unRAID then used OS X disk tools to extend the boot partition (entered size directly) and let it execute rebooot --> dead sign ø Is there a different step list?

Same for me. For an unknown reason (Nothing changed beside update to 6.3.2 some days back) the server become unresponsive (Web GUI and Shares). I can still use the SSH connection so. Is there any command to restart the web server or get diagnostics data? Shutdown -rF does not do the reboot (waited 1 hour and hard rebooted ending up in Parity scan)

Hello all - I'm experiencing a reboot loop after the update from 6.2.4 to 6.3.0 this morning. The last line after regular mode or safe mode is the bzroot entry. The server immediately reboots after that line was printed to screen. Funny so, the GUI Mode works and all dials are taken in the guide mode started server. I've tried to give him a cleanup and retry chance but as soon as I use the regular or safe mode I'm back in the reboot loop... Any idea where I can look for details to fix it? Is there anything logged when it is rebooting directly after bzroot? fatmax-diagnostics-20170204-1652.zip

I'm unsure where to look... Search was not successful and Logfiles are not stating any errors. Any VM I've created (using standard values) does not boot beyond the BIOS screen with the assigned memory. Any ideas where I can look for the root cause? Example Log file (Non showed an error line): 2017-01-01 18:09:31.709+0000: starting up libvirt version: 1.3.1, qemu version: 2.5.1, hostname: FatMax LC_ALL=C PATH=/bin:/sbin:/usr/bin:/usr/sbin HOME=/ QEMU_AUDIO_DRV=none /usr/local/sbin/qemu -name Ubuntu -S -machine pc-q35-2.5,accel=kvm,usb=off,mem-merge=off -drive file=/usr/share/qemu/ovmf-x64/OVMF_CODE-pure-efi.fd,if=pflash,format=raw,unit=0,readonly=on -drive file=/etc/libvirt/qemu/nvram/ddce4f00-e106-6864-3579-589b9ff61b8c_VARS-pure-efi.fd,if=pflash,format=raw,unit=1 -m 4096 -realtime mlock=off -smp 4,sockets=1,cores=4,threads=1 -uuid ddce4f00-e106-6864-3579-589b9ff61b8c -no-user-config -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/domain-Ubuntu/monitor.sock,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc,driftfix=slew -global kvm-pit.lost_tick_policy=discard -no-hpet -no-shutdown -boot strict=on -device i82801b11-bridge,id=pci.1,bus=pcie.0,addr=0x1e -device pci-bridge,chassis_nr=2,id=pci.2,bus=pci.1,addr=0x1 -device ich9-usb-ehci1,id=usb,bus=pcie.0,addr=0x7.0x7 -device ich9-usb-uhci1,masterbus=usb.0,firstport=0,busv=charchannel0,id=channel0,name=org.qemu.guest_agent.0 -device usb-tablet,id=input0 -vnc 0.0.0.0:0,websocket=5700 -k en-us -device qxl-vga,id=video0,ram_size=67108864,vram_size=67108864,vgamem_mb=16,bus=pcie.0,addr=0x1 -device usb-host,hostbus=1,hostaddr=3,id=hostdev0 -device virtio-balloon-pci,id=balloon0,bus=pci.2,addr=0x4 -msg timestamp=on Domain id=3 is tainted: high-privileges char device redirected to /dev/pts/0 (label charserial0) 2017-01-01T18:10:31.884723Z qemu-system-x86_64: terminating on signal 15 from pid 17485 2017-01-01 18:10:32.084+0000: shutting down

From unassigned drive to the unRAID Drive --> MC via SSH (could also be done with an script and the Plugin User Scripts) From an array drive to another drive in the array --> unbalance Plugin

Hi Chadskie - I'm running a similar setup and it works quite well. MB: have a Look at the Supermicro X11SSL-CF This comes with 6 SATA and 2 SAS (Breakout to 8 SATA) Ports. Resulting In an total of 14 ports. Other specs are very similar to your selection CPU: I've picked the Xeon E3-1260L v5 @ 2.90GHz as it runs at a very low Wattage (45W) with an impressive passmark of 10k. The whole system is consuming approx. 40W with all drives spun down but fully responsive due to the SSD Cache and folder caching plugin. Max Power consumption was 105W with Plex doing the enumeration of the whole library during an parity scan... Cache: Running 2 Samsung Evo 750 500GB in RAID1 mode. Decided to not use it for the Plex mediathek share and only use it for the dockers & VMs. Plex will delay the playback by 3-5 seconds If the drive needs to spin up. Acceptable for me.. RAM: I ran with 16GB and it was enough. I've updated to 32GB only for VM usage. Plex is running fine off the SSD Cache and 16GB RAM But definitely go with 2 modules in the beginning... My system Summary: Case: Antec 1900 (offers 14 HDD/SSD Slots plus 4 additional via the 5.25 Bays) PSU: be quiet! Pro10 650W Nice SATA Power connectors available... MB: Supermicro X11SSL-CF (comes with 14 SATA ports --> Matching the 14 Bays of the case CPU: Intel Xeon E3-1260L v5 @ 2.90GHz comes with 10k Passmarks to run 5 parallel transcoding streams in Plex @ 45W! CPU Heatsink: be Quiet Pure Rock as the smallest is already more than covering the CPU Wattage... RAM: 4x 8GB CL15 PC4-17000 DDR4 UDIMM-Module from Crucial The drives are mostly from my old setup, extended by matching drives (1x SSD, 1x Parity, 2x WD Red) HDD: 1x WD Black 4TB for Parity, 2x WD Green 3TB, 4x WD Red 4TB SSD: 2x Samsung EVO 750 500GB A drive outside of the array Is possible (via the unassigned drives plugin) but it will not be covered by parity! You can define a new share and only allow a certain drive to be utilized. This would save all data to the dedicated drive and keeps it save with parity.

CA calculates the appdata size by looking at the paths mapped to the docker app. If there are multiple paths present that could potentially be appdata it'll flip a coin Sent from my LG-D852 using Tapatalk That would be a nice feature request: CA App Store with option to select/define path that being considered for reporting for installed docker

Silly question about the Apps Ressource Monitor reporting on the AppData Size... The PleyPy need the path to the Plex Logs. App Reporting is now calculating the size of Plex's Logs Folder instead of the PlexPy AppData. Is there anything I oversee in the setup? Also not sure if this is the right thread or if it needs to be under the CA App Store Thread

Do you have an root password set? This is mandatory.

The iOS app is functional after the main issue was resolved. If no root password is set (I've forgot to set one after the rebuild of the USB key) it worked like a charm. General hint: no root pw = no ControlR functionality Gesendet von iPad mit Tapatalk

Not sure what that is. PEBKAC = Problem Exists Between Keyboard And Chair Layer 8 = The individual person Another similar one (no offence Trebon74) is ID-10-T error.... Yeah forgot about that one I switched to the right support tread as it seems to be a chained issue and getting the plugin up and running would most likely solve the iOS lookup problem as well. initially thought of iOS App is an alternative interface to the web page running on the unRAID server...

Can you check the log (should be at /usr/local/emhttp/plugins/controlr/controlr.log) for any warnings ? Send it over pm or email if you want. I'll change the log location in the next release. There is no *.log file in that folder. I am having the exact same problem. I cannot login: unable to connect to server 401 (unauthorized). Similar to interwebtech no log file being created. Same for me. No log file on the given location. Looked at the new given location of /boot/logs/controlr.log It seems that the issue is related to W: 2016/12/11 18:39:25 server.go:152: Must log in as root W: 2016/12/11 18:39:38 server.go:192: Unknown encryption type: () Have reinstalled the companion plugin --> No change Created controls user --> No change, cannot assign as I can't login as root iOS App does not find the server (seems that the companion plugin needs to be fixed first) Plugin: v1.1.1 unRAID v6.2.4

I can't get it to work in any way Situation Headless unRAID server (link pointing to localhost is not correct as I always use an remote browser) login mask does not accept any password/user combination that exists on my unRAID system. I would expect root to be functional. Always error code 401 (unauthorized). the iOS app also does discover the server. It also seems that the server's IP address is skipped faster then the other IPs in the segment. it all seems to be related to an rights issue... ControlR Plugin v1.1.1 iOS App v2.3.0 unRAID server v6.2.4 system log state: Dec 11 10:38:57 FatMax php: /usr/local/emhttp/plugins/controlr/scripts/start Dec 11 10:38:57 FatMax sudo: root : TTY=unknown ; PWD=/usr/local/emhttp ; USER=root ; COMMAND=/bin/bash -c /usr/local/emhttp/plugins/controlr/controlr -port 2378 any Layer-8/Pebkac (me) issues here?

Ok then I'll get out and will enjoy the sun Using top. on the console shows the preclear tasks and I've found the log files for the finished jobs... All good for now I guess that even a 10k Passmark CPU on an modern server board can have some sort of a bottleneck Thanks for the hint. Gives me hours of not troubleshooting

I'm pre clearing 4TB drives and startet an test array with 3 1TB disks without parity. As soon as I clicked start the array. the web GUI became unresponsive and I'm no longer able to get anything using the browser. Ping: OK SSH: OK TOP shows preclear is still doing it's job (for at least 12 more hours) How do i restart the web server from the SHH console? I don't want to reboot the server to avoid the preclear to rerun searching the board was not answering my question Thanks a lot

Hi there - I'm scrubbing my head as I don't get any helpful error messages from the login. telnet -l root <myServer> --> entering password (double checked it is entered correctly) --> long pause (5 sec.) --> Login failed. Is telnet not enabled for root? If I use SSH it works like a charm. I've also created another user using the web GUI. Telnet immediately terminates the session as the user is not allowed. This is pretty clear. So, what's wrong (or I'm doing wrong) with telnet and root in unRAID 6.2? 2nd Question: As I created an user, how to manage rights (not file system) within Slackware? It's only within the shell, not within the web GUI? Or I'm just too blind Thanks for helping a nooby

Thanks a lot Parts ordered... Let's see how my first unRAID will become real