TheBlueKingLP

No, no docker/vm is using it. I’ve tried to disable docker and cam completely, but the roots still filling up

Is there a way to check what is using it or what is the mount point?

It happens even I’ve disabled docked entirely. also disabled vm manager

Ah, sorry about that. I’ve forgotten to post it. pegasus-diagnostics-20190310-1407.zip edit: I downloaded it when it is around 73% full

Bump

Sorry for not zipping it, I was using my iPhone to post that. Also, after the system rootfs if full, I couldn't get the diagnostic. I will post the diagnostic file of "when the rootfs is not full" tomorrow as it is now passed midnight for me

Here is the syslog.txt Also, I noticed the rootfs is full, I think this is what caused it,but why was it full in the first place?(It will go back to normal once I reboot.)

Chkdsk report no error, I am already using a usb2 port. Here is the syslog file: https://pastebin.com/TK5SJw1K

I was going to upload the diagnostic if I could, but after it started to report 0 disk, the diagnostic button stopped working. I haven’t restarted the server yet, what could I do to get diagnostic working again?

My unRAID Server running on 6.7.0-rc5 will report “*Notice [] - array health report [PASS]* Array has 0 disks” after around 26 hours of uptime. At this time: Web UI sometimes stopped working Dockers and VMs stays running fine with no issue. Server info is blank Smb stopped working No raid card, 6x1TB consumer hdd Cable known good and not loosen MB: Asus rampage v edition 10 P.s. If you need more info please ask for it

My array health report will say it has 0 disk after the server has been on for some time. Diagnostic is not working

I didn't cancel it or stop it

After I used unBALANCE to move all of my files from an unencrypted disk to a new encrypted disk(both are 1TB drive), there are still around 500gb of files still in the old disk and the new disk was already full (around 300mb space left), where did the extra 500gb of files came from? The move operation had already finished.

i want to search for files that exist on multiple disk, e.g. File access.log exist on /mnt/disk1/service/access.log and /mnt/disk5/service/access.log

I have a new 1TB wd blue hard drive but when I try to pre clear it, it stuck at starting.

Is that a unassigned device?

You could refer to this (http:// ) guide made by Spaceinvader One

Hmm, ok, maybe make a bug report then?

Thank you for your help. At the mean time I will switch back to the old method. Please post here after you've done testing the new result.

Here is the controller that I wanted to passthrough in the lspci -v output 07:00.0 USB controller: ASMedia Technology Inc. ASM1142 USB 3.1 Host Controller (prog-if 30 [XHCI]) Subsystem: ASUSTeK Computer Inc. ASM1142 USB 3.1 Host Controller Flags: bus master, fast devsel, latency 0, IRQ 18, NUMA node 0 Memory at fb800000 (64-bit, non-prefetchable) [size=32K] Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [68] MSI-X: Enable+ Count=8 Masked- Capabilities: [78] Power Management version 3 Capabilities: [80] Express Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [200] Advanced Error Reporting Capabilities: [280] Secondary PCI Express <?> Capabilities: [300] Latency Tolerance Reporting Kernel driver in use: xhci_hcd 08:00.0 USB controller: ASMedia Technology Inc. ASM1142 USB 3.1 Host Controller (prog-if 30 [XHCI]) Subsystem: ASUSTeK Computer Inc. ASM1142 USB 3.1 Host Controller Flags: bus master, fast devsel, latency 0, IRQ 16, NUMA node 0 Memory at fb700000 (64-bit, non-prefetchable) [size=32K] Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [68] MSI-X: Enable+ Count=8 Masked- Capabilities: [78] Power Management version 3 Capabilities: [80] Express Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [200] Advanced Error Reporting Capabilities: [280] Secondary PCI Express <?> Capabilities: [300] Latency Tolerance Reporting Kernel driver in use: xhci_hcd

On the flash boot drive inside the config folder (/boot/config/vfio-pci.cfg)

I am switching to the new 6.7.0-rc1 "config/vfio-pci.cfg" but it didn't work. The usb controller I am trying to passthrough didn't show in other pci devices in the vm manager. Here is the content of the vfio-pci.cfg file: BIND=07:00.0 08:00.0

oh, ok, it worked this time. sorry about that.

I disabled bond and bridge for eth1 but still not available as selection item for bond0