lankanmon

Hey, sorry, I am unable to see any of my docker images due to Docker Service failing to start... Is there any other way?

Okay, thanks! So, if I delete the image and restart docker, I should be able to see the application templates? Is there anyway to see the custom docker networks before I delete the image? Just so I can re-make it. I think I had one setup... Thanks!

My cache drive became full due to an unexpected set of data baing added to cache only. I only nocied when some of my docker apps started misbehaving. I turned off docker (in settings) to prevent further damage and ran the mover to get the cache back to normal. When turning on docker again, I saw that "Docker Service failed to start.". I know that I can delete the docker image, but IIRC, last time I deleted the image, I had to setup each app all over again. Since then, I have a lot more apps. Is there a way to backup each of the apps configs (all of the settings) before deleting the image, so I can add them easily after deleting the image? Since the docker image is not starting, I can't go through each of then like I would normaly to take screenshots of the settings. Your help will be much apprciated. I really hope that I don't need to figure out the configs for each app all over again... I have also attached my diagnostics in case that will help with resolvign the issue... lknserver-diagnostics-20200920-0710.zip

Hey thanks for this. I swapped out a bunch of SATA cables and it seems to have stopped the messages. I will keep an eye on it for now. Good to know that the drive is okay.

Okay, I will try swapping the cable and if that does not work, I will swap the drive... Can you think of anything else it could be?

I waited about a day after and it seems to be back. Fix common problems shows: Unable to write to cache and the log is about 34% full now. I do not have docker and vms running so it is just system messages causing the errors. I have attached diagnostics. Also do I need to balance my cache? and if so, what command should I use? lknserver-diagnostics-20200108-2158.zip

Here is the diagnostics after I made sure the cables a plugged in correctly. lknserver-diagnostics-20200107-2359.zip

So, I need to replace the cache drive?

I am getting a BTRFS error spamming my logs and there appears to be other issued. SDB1 is my cache drive. I have Fix common problems installed and it is detecting that the drive is read only or full. But the drive is 480GB and it is only using 78GB, so there is plenty of space. I have attached the diagnostics to this post This is a snippet of the message being spammed: Jan 6 05:12:23 LKNServer kernel: __btrfs_lookup_bio_sums: 10 callbacks suppressed Jan 6 05:12:23 LKNServer kernel: BTRFS info (device sdb1): no csum found for inode 988745 start 0 Jan 6 05:12:23 LKNServer kernel: sd 1:0:0:0: [sdb] tag#5 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 Jan 6 05:12:23 LKNServer kernel: sd 1:0:0:0: [sdb] tag#5 CDB: opcode=0x28 28 00 03 d0 92 b8 00 00 08 00 Jan 6 05:12:23 LKNServer kernel: print_req_error: I/O error, dev sdb, sector 64000696 Jan 6 05:12:23 LKNServer kernel: BTRFS error (device sdb1): bdev /dev/sdb1 errs: wr 43, rd 254421, flush 0, corrupt 0, gen 0 Your help is much appreciated. Thanks! lknserver-diagnostics-20200107-0159.zip

Awesome! I'll take a look, thanks!

I have a main server with with all of my storage and a decent spec (as seen in my signature). I want to set up a secondary unraid server with SSDs only to use as a secondary "hot" server which will take a bit more of the processor intensive tasks. How can I pass the shares between them? Example: I want to have a Plex Media Server on the new one that will be used for remotely viewing content and it will need to encode to different formats. When I am attempting to install the Plex docker app, all I can do is pass in directories, not network locations. How can I achieve this?

I have been using Unraid for about five years for work (with my own license for about three years). I have a hard time remembering my life before I learned of Unraid. I have always been a Data Hoarder at heart, but did it chaotically. Setting up RAID arrays have always caused me anxiety, purely for the fact that if I make a mistake, I can loose all the data (since it is striped). When I learned of Unraid and its use for data, virtualization and the built in docker support, it was obvious what I will use for my own server. Happy Birthday Unraid!

I followed this video as shown to get Let's Encrypt to run on my server with my own domain. It works well for my docker containers! One thing that I am not clear about how to do is to point one sub domain (that I already have gotten a certificate for) to a VM which has an instance of GitLab running. It was the only thing that I had exposed to web before setting up this reverse proxy and would like to still be able to access it from a subdomain. Your help to achieve this would be greatly appreciated... Thanks!

@Squid & @Saldash I just freshly installed firefox on a laptop that I never used (with no plugins) and also on android (w. chrome and firefox - also no plugins) and it is still happening. Furthermore, I am using uBlock Origin and I have added the server ip to the whitelist and it is still happening. Any ideas?

Hi all, I have noticed recently that clicking a docker app and selecting WebUI does not seem to work on both Chrome and Firefox. On chrome, it opens a new tab with the url: about:blank#blocked On firefox, it does nothing (no tab or window opened) I have tested on different browsers, operating systems, and devices. I have also ensured that my adblocker is disabled to ensure that is not the cause of the issue. Any help would be greatly appreciated! Thanks!