benyaki Posted December 30, 2020 Share Posted December 30, 2020 So I have an ageing server that I have new hardware here to replace (almost all parts, waiting on some HBAs so I can connect all the drives to transfer to new larger ones). Everything was running fine, then I had a problem with the bios being corrupted, replaced the BIOS chip. That finally arrived in the mail. Booted up the system last night, everything was OK, started going through and cleaning up some items (older dockers not in use and changed from 2 cache pool down to 1 cache drive. Tried rebooting - no WebUI. Can boot into safe mode, but still no webui access or telnet. Disable autostart. Removed ALL plugins, can access WebUI again. Great! Except - the first plugin that I add back in - Community Applications, installs properly, looks good, so I reboot to make sure everything works - again, no telnet or WebUI! Shutdown and remove the plugin, can access again. I have attached diagnostics from when a few plugins were installed but it is the same result. Anyone have any ideas? Would like to get this all running and before I switch over to new hardware. Thanks! tower-diagnostics-20201230-1531.zip Quote Link to comment
trurl Posted December 30, 2020 Share Posted December 30, 2020 According to diagnostics most of your disks are not assigned. Is this expected? Quote Link to comment
benyaki Posted December 30, 2020 Author Share Posted December 30, 2020 It could be that I just ran diagnostics really quickly after it booted and they have not been assigned yet - noticed that on the GUI that they take a few seconds to show up. Just to add - I just tried removing CA, added in a couple other plugins (unbalance and unassigned devies) - still prevents me from accessing the WebUI or terminal. One thing I did notice earlier was that before when all the plugins were still installed - either in safe mode or normal, I could not ping any address. I just checked now on command line on the machine and can ping an IP address (again, unbalance and unassigned devices are installed, but still no WebUI or telnet access) Quote Link to comment
trurl Posted December 30, 2020 Share Posted December 30, 2020 Just now, benyaki said: It could be that I just ran diagnostics really quickly after it booted and they have not been assigned yet No. In fact, syslog specifically says most of your drives are missing, though smart folder is showing a lot of disks that are not assigned. I see you have Marvell controllers. Those are not recommended, but it seems unusual that the assigned disks would be missing and are instead showing up as unassigned. I see you replaced BIOS. If your BIOS has enabled IOMMU (VT-d or according to wikipedia AMD calls it AMD-Vi) then that might cause problems with those Marvell controllers that you didn't have before. Quote Link to comment
benyaki Posted December 30, 2020 Author Share Posted December 30, 2020 (edited) Booted it back up, everything was assigned properly, there were 2 unassigned devices (1 which I have in there for no reason, and the second which was the cache drive that was just removed). The SATA drives are all attached the PCI-X controller cards (Supermicro something-something, cant remember). Nothing on the motherboard. Anyways, because I was bored, I setup the bare minimum for the new hardware, booted it up (obviously without any drives attached) and it seems to have no problem with the plugins that were installed, whereas with the other (old) motherboard, it still has the problem. I am going to put it down to the new BIOS, and hope for the best on the new hardware? Edited December 30, 2020 by benyaki Quote Link to comment
trurl Posted December 30, 2020 Share Posted December 30, 2020 Do you know your disk assignments? How many parity disks did you have? It is especially important that you not assign any data disk to any parity slot or it will be overwritten by parity. And if you have parity2 the disks must be assigned exactly as before or parity2 will be invalid. Quote Link to comment
benyaki Posted December 30, 2020 Author Share Posted December 30, 2020 Yes, I made sure to grab a screen capture of the drives, their slots etc while it was working. dual parity, I’ll probably cut that down to single as I am moving down to 4 data drives at 12tb each. Or 3 12tb drives, a few 4tb drives, and dual parity. Quote Link to comment
benyaki Posted December 31, 2020 Author Share Posted December 31, 2020 Thanks for the help and looking into this BTW. much appreciated! Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.