chadesh Posted December 25, 2021 Share Posted December 25, 2021 A couple days ago I wanted to setup shinobi camera docker to monitor a few cameras. Unfortunately I never got that far. I started noticing that only 2 of my nics were even seen by unraid. I noticed this when anytime I tried to change network setting the server would just sit there saying it was configuring interface. I let it sit for the whole day and it did nothing. I had to delete the network config file a few times. I even went into the bios to see if they(network cards) were enable and all of them were. The board I am using is Fatal1ty Z270 Professional Gaming i7 w/ I7 6700K 32gigs. When things were working It showed only one intel and the AQUANTIA® 5 Gigabit LAN. this has 3 ethernet and 1 wifi. What I was going to try to do is use 1 intel for unraid and the other intel for the shinobi docker, but it seems any time I change any network settings unraid get mad and loses connection. Also I already deleted the network config file and it still won't connect. I have a keyboard and mouse and monitor hooked up. I have never seen a prompt that I could enter commands into. Quote Link to comment
itimpi Posted December 25, 2021 Share Posted December 25, 2021 If you want any sort of informed feedback you should attach your system’s diagnostics zip file to your next post in this thread. Quote Link to comment
chadesh Posted December 25, 2021 Author Share Posted December 25, 2021 I would, but as I said I don't have a prompt to do any commands Quote Link to comment
Squid Posted December 25, 2021 Share Posted December 25, 2021 26 minutes ago, chadesh said: I would, but as I said I don't have a prompt to do any commands As in what? When booting up you get a ton of text scrolling by and then it winds up at a blank screen? Boot into the non-gui mode Quote Link to comment
chadesh Posted December 25, 2021 Author Share Posted December 25, 2021 1 minute ago, Squid said: As in what? When booting up you get a ton of text scrolling by and then it winds up at a blank screen? Boot into the non-gui mode No the text is there, but there is no where to type in commands and I've never used gui mode, even tried safemode without plugin and gui and still nothing.. Also I tried to restart it one more time and it finally booted and I have access to the web gui. Even though it seems to be fixed. I attached the diagnostic . Maybe someone can help me figure out why only 2 of my nics are showing. 😊 systemnas-diagnostics-20211224-2012.zip Quote Link to comment
Squid Posted December 25, 2021 Share Posted December 25, 2021 28 minutes ago, chadesh said: help me figure out why only 2 of my nics are showing There's 3 showing with a cable plugged into one of them Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 2500baseT/Full 5000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 100baseT/Full 1000baseT/Full 2500baseT/Full 5000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: Unknown! Duplex: Unknown! (255) Auto-negotiation: on Port: Twisted Pair PHYAD: 0 Transceiver: internal MDI-X: Unknown Supports Wake-on: pg Wake-on: g Current message level: 0x00000005 (5) drv link Link detected: no driver: atlantic version: 5.10.28-Unraid firmware-version: 1.5.44 expansion-rom-version: bus-info: 0000:0c:00.0 supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: yes supports-priv-flags: yes -------------------------------- Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: Unknown! Duplex: Unknown! (255) Auto-negotiation: on Port: Twisted Pair PHYAD: 1 Transceiver: internal MDI-X: off (auto) Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: no driver: igb version: 5.10.28-Unraid firmware-version: 0. 4-1 expansion-rom-version: bus-info: 0000:08:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: yes -------------------------------- Settings for eth2: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: on Port: Twisted Pair PHYAD: 1 Transceiver: internal MDI-X: on (auto) Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: yes driver: e1000e version: 5.10.28-Unraid firmware-version: 0.2-4 expansion-rom-version: bus-info: 0000:00:1f.6 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: yes -------------------------------- Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.