Blu Posted May 26, 2011 Share Posted May 26, 2011 Basically I ordered an antec twelve hundred case (link) and am going to be using four of the Supermicro Black 3X5.25 to 5X3.5IN SATA Drive Bay Converter (link) Do you think I'll need to mod the case by cutting off the little ledges that would be in place to hold up a 5.25" optical drive or will the bay converter just sit on them normally? If I was needed to mod the case would I need to grind down all of the ledges or just leave 1 every 3 spaces meaning to leave 4 ledges for the converters to rest on. Thanks for any advice on this. Link to comment
aRe-eYe-pEa Posted May 26, 2011 Share Posted May 26, 2011 Most people on this forum have stated that using a C clamp and a cloth to protect the case while you bend the metal pieces out of the way. Link to comment
KYThrill Posted May 26, 2011 Share Posted May 26, 2011 I guess I'm primitive. I've always used a hammer and a 2x4. Link to comment
aRe-eYe-pEa Posted May 26, 2011 Share Posted May 26, 2011 I am sure that gets the job done too. It might help releave a little stress at the same time. Link to comment
prostuff1 Posted May 26, 2011 Share Posted May 26, 2011 C-clamp it. It works really well and it easy enough. It is time consuming, but does a good job. Link to comment
Blu Posted May 26, 2011 Author Share Posted May 26, 2011 When you guys say c-clamp it do you just mean to bend it backwards like this? |--- <(clamp) ---|<(clamp) Bending it straight backwards right? (Edit: Damn this case weighs a ton as well...No joke it's got to be atleast fifty pounds) Link to comment
vca Posted May 26, 2011 Share Posted May 26, 2011 Are there any 4 in 3 or 5 in 3 cages that have groves in the side that would accommodate these "ledges" without modification? Stephen Link to comment
Blu Posted May 26, 2011 Author Share Posted May 26, 2011 Are there any 4 in 3 or 5 in 3 cages that have groves in the side that would accommodate these "ledges" without modification? Stephen As far as I know I don't believe so...Can someone sorta show me an example of how to do this with a c clamp? A hammer and a 2by4 is sounding good it just doesn't sound like it will bend out clearly and if I was to bend them with a hammer or c-clamp is it possible to bend them back if say I wanted to use this case for a pc later in the road, which I doubt cause I'll always want a file server Link to comment
S80_UK Posted May 26, 2011 Share Posted May 26, 2011 When you guys say c-clamp it do you just mean to bend it backwards like this? |--- <(clamp) ---|<(clamp) Bending it straight backwards right? Something like this... | | |--- <(clamp) | | |<(clamp) | Bending it so that the tab that projected is now in line with the rest of the sheet metal rather than with a 90 degree bend in it. Link to comment
christuf Posted May 26, 2011 Share Posted May 26, 2011 I used some pliers to get a small angle, then clamp across to push the tab flat. It does take some effort - some are easier to get the C-clamp to than others. Best advice is to get the biggest C-clamp you can. Link to comment
PeterB Posted May 27, 2011 Share Posted May 27, 2011 Are there any 4 in 3 or 5 in 3 cages that have groves in the side that would accommodate these "ledges" without modification? 4 in 3 - yes 5 in 3 - no, there simply isn't enough space. 5 drives needs the full 5 1/4 width. Link to comment
GabrielB Posted May 31, 2011 Share Posted May 31, 2011 When you guys say c-clamp it do you just mean to bend it backwards like this? |--- <(clamp) ---|<(clamp) Bending it straight backwards right? Something like this... | | |--- <(clamp) | | |<(clamp) | Bending it so that the tab that projected is now in line with the rest of the sheet metal rather than with a 90 degree bend in it. By any chance, can someone post a before and after pic of the tab bending technique? Link to comment
Recommended Posts
Archived
This topic is now archived and is closed to further replies.