PzrrL Posted October 12, 2022 Author Share Posted October 12, 2022 I can't wait and just started without checking the box, will that be alright? Quote Link to comment
PzrrL Posted October 12, 2022 Author Share Posted October 12, 2022 Result: UUID: hidden Scrub started: Thu Oct 13 00:57:18 2022 Status: finished Duration: 0:09:33 Total to scrub: 412.41GiB Rate: 736.64MiB/s Error summary: no errors found Quote Link to comment
JorgeB Posted October 12, 2022 Share Posted October 12, 2022 Looks good for the moment, and now if one device fails pool should continue working, but of course should be fixed ASAP, also see here for better pool monitoring, you'll need to reset the current errors as explained there. Quote Link to comment
PzrrL Posted October 12, 2022 Author Share Posted October 12, 2022 @JorgeB million thanksssss! I have already setup the monitor following the post provided. May you also provide guidance on swapping out the faulty cache drive? Besides, do you recommend do the upgrade of unraid first or swapping first? Thanks. Quote Link to comment
JorgeB Posted October 12, 2022 Share Posted October 12, 2022 Upgrade first since that functionally is broken on v6.9, then see here: https://forums.unraid.net/topic/46802-faq-for-unraid-v6/?do=findComment&comment=480419 Quote Link to comment
PzrrL Posted October 13, 2022 Author Share Posted October 13, 2022 @JorgeB Unfortunately the monitor is raising errors not long after the scrub. Do I need to re-do all the steps in order to make sure the cache drives are in sync before swapping? Regarding the link you sent, can I do the following as I don't have enough ports: 1. Stop the array and shutdown 2. Swap the faulty ssd 3. Power Up 4. Assign the new device in the faulty's SSD slot? 5. Start the array 6. Wait for cache copying to complete Is this procedure okay? Thanks! Quote Link to comment
JorgeB Posted October 13, 2022 Share Posted October 13, 2022 5 hours ago, PzrrL said: Do I need to re-do all the steps in order to make sure the cache drives are in sync before swapping? Depends on if the errors are from the device you're going to remove, best to post new diags. Quote Link to comment
PzrrL Posted October 13, 2022 Author Share Posted October 13, 2022 # btrfs dev stats /mnt/cache [/dev/sdi1].write_io_errs 475032 [/dev/sdi1].read_io_errs 3675 [/dev/sdi1].flush_io_errs 55531 [/dev/sdi1].corruption_errs 0 [/dev/sdi1].generation_errs 0 [/dev/sdj1].write_io_errs 0 [/dev/sdj1].read_io_errs 0 [/dev/sdj1].flush_io_errs 0 [/dev/sdj1].corruption_errs 0 [/dev/sdj1].generation_errs 0 uncrate-diagnostics-20221013-2223.zip Please have a look thanks! Quote Link to comment
JorgeB Posted October 13, 2022 Share Posted October 13, 2022 It's the Intel SSD again, if that's the one you were going to replace you can go ahead, and the steps you mentioned above are correct. Quote Link to comment
PzrrL Posted October 13, 2022 Author Share Posted October 13, 2022 Thanks I just swapped the disk. Should I actually upgrade first? Or it will be fine if I do the swapping then the upgrade? Quote Link to comment
JorgeB Posted October 13, 2022 Share Posted October 13, 2022 Like mentioned before you must upgrade first or it won't work. Quote Link to comment
PzrrL Posted October 13, 2022 Author Share Posted October 13, 2022 Sorry I am a bit confused on the steps right now. I should start the array with both cache drive (the old one) perform an upgrade Confirm upgrade successful Swap cache drive as the steps I mentioned above rebuild the cache pool Is this correct? Quote Link to comment
JorgeB Posted October 13, 2022 Share Posted October 13, 2022 You can do the upgrade now and instead of rebooting power off and replace the SSD, then just check that it's on the new release after boot. Quote Link to comment
PzrrL Posted October 14, 2022 Author Share Posted October 14, 2022 Thanks @JorgeB I did an upgrade and see I am on 6.11.1 now. I also replaced the SSD and built the pool without problem. Is there any final check needed? Thanks! uncrate-diagnostics-20221014-2142.zip Hopefully this will be the final diags. Quote Link to comment
Solution JorgeB Posted October 14, 2022 Solution Share Posted October 14, 2022 Pool looks good so far. Quote Link to comment
PzrrL Posted October 14, 2022 Author Share Posted October 14, 2022 Great thanks a million @JorgeB you have been really patient and helpful!!! Speechless thanks going through this with me!!! 2 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.