Olymoly Posted August 18, 2023 Share Posted August 18, 2023 Good evening, A few weeks ago, i came across a Disk Disabled. i didnt noticed any issues until i checked the GUI, after setting and forgetting the server. i was wondering what could of happened? What i can tell there is a i/o error on disk 9. (im learning i swear, haha) i will assume that i will need to replace a disk and rebuild from partiy disk. can i replace this disk with a larger disk than the disable disk that is within the size limits of the array? do i need to replace it with the same size and then replace that disk with the larger one? Attached are the latest diagnostics. thank you nastradamus-diagnostics-20230818-0157.zip Quote Link to comment
JorgeB Posted August 18, 2023 Share Posted August 18, 2023 It's logged as a disk problem, run an extended SMART test on disk9, also make sure you enable system notifications so you get notifief when there's a problem. Quote Link to comment
Olymoly Posted August 18, 2023 Author Share Posted August 18, 2023 smart test completed and returned a read failure. i believe i did set up notification, sent to an email and filter/labeled. i just never looked at the email account. until i did. Quote Link to comment
itimpi Posted August 18, 2023 Share Posted August 18, 2023 3 hours ago, Olymoly said: can i replace this disk with a larger disk than the disable disk that is within the size limits of the array? You can replace it with a larger disk if it is no larger than the smallest parity drive. If you want to upgrade parity to a larger size and use the old parity drive as the replacement then there is the parity swap procedure for this special case. Quote Link to comment
Olymoly Posted August 19, 2023 Author Share Posted August 19, 2023 17 hours ago, itimpi said: You can replace it with a larger disk if it is no larger than the smallest parity drive. If you want to upgrade parity to a larger size and use the old parity drive as the replacement then there is the parity swap procedure for this special case. i have a cold spare 16tb, i have dual paritied 16tb drives. the drive that failed the extended smart test is 8tb. based on the first part of your answer, i could replace the drive with the 16tb cold spare. i would not need a parity swap as i dont need to update parity to a larger size. Quote Link to comment
itimpi Posted August 19, 2023 Share Posted August 19, 2023 3 hours ago, Olymoly said: based on the first part of your answer, i could replace the drive with the 16tb cold spare. i would not need a parity swap as i dont need to update parity to a larger size Yes. If you put in the 16TB drive Unraid will first rebuild the contents of the 8TB drive and after completing the rebuild expand the file system to fill the whole 16TB. If the full 16TB is not immediately made available after the rebuild you made need to reboot to get this to happen (although in theory this should not be required). Quote Link to comment
Olymoly Posted August 19, 2023 Author Share Posted August 19, 2023 (edited) just of a bit of clearity, ill just shutdown, pull the disk and replace it with a new disk? rebuild from there? seems simple enough, also i just remembered that i dont have an open slot for another drive either for preclear etc. Edited August 19, 2023 by Olymoly Quote Link to comment
Solution JorgeB Posted August 19, 2023 Solution Share Posted August 19, 2023 28 minutes ago, Olymoly said: ill just shutdown, pull the disk and replace it with a new disk? rebuild from there? Yes. Quote Link to comment
Olymoly Posted December 24, 2023 Author Share Posted December 24, 2023 On 8/19/2023 at 4:52 AM, Olymoly said: seems simple enough, also i just remembered that i dont have an open slot for another drive either for preclear etc. after ive pulled the old disk and replace with a new disk, can i start the array while parity emulating the missing disk and preclear the new disk before i rebuild parity on the new disk. would i just start the array with a rebuild and preclear? would this cause an issue? Quote Link to comment
JorgeB Posted December 24, 2023 Share Posted December 24, 2023 26 minutes ago, Olymoly said: can i start the array while parity emulating the missing disk and preclear the new disk before i rebuild parity on the new disk. You can but I would just rebuild to get the array back to protected as soon as possible. 1 Quote Link to comment
Olymoly Posted December 24, 2023 Author Share Posted December 24, 2023 3 minutes ago, JorgeB said: You can but I would just rebuild to get the array back to protected as soon as possible. cool, as i thought. as this is my greatest worry. just wanted wanted a second opinion given the emphasis on how important is it to preclear a new disk. thank again jorge Quote Link to comment
itimpi Posted December 24, 2023 Share Posted December 24, 2023 6 minutes ago, Olymoly said: cool, as i thought. as this is my greatest worry. just wanted wanted a second opinion given the emphasis on how important is it to preclear a new disk. thank again jorge A preclear is not as important if you are using it as a replacement disk as the rebuild process writes to every sector anyway. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.