extrakaese Posted August 31, 2023 Share Posted August 31, 2023 Hi, suddenly I had read errors on two hard drives. One was disabled, the other was not. Both SMART values are ok, both hard drives are on the same power cable. After I stopped the array and restarted, the errors on both hard drives were gone, but one hard drive remains disabled and as emulated. Â I don't know much about this and am afraid I am doing something wrong. I have two parity hard drives. Â Is there anyone out there that can help me? Â I also have the logs since this morning. Â Thank you very much in advance. syslog.txt Quote Link to comment
JorgeB Posted August 31, 2023 Share Posted August 31, 2023 Please post the complete diagnostics. Quote Link to comment
extrakaese Posted August 31, 2023 Author Share Posted August 31, 2023 Have the server unfortunately already restarted and only afterwards read that i can only save them before. Â Just did a SMART test on the hard drive and I was recommended by a friend to restore the data, so data rebuild because everything else is ok only the hard drive was disabled, should I do that? Quote Link to comment
JorgeB Posted August 31, 2023 Share Posted August 31, 2023 If SMART look OK, and since having two disks with issues at the same time was most likely a power/connection issues, you can rebuild on top, make sure the emulated disk is mounting and contents look correct before doing it, also a good idea to check/replace cables before doing it, to rule that out. Quote Link to comment
extrakaese Posted August 31, 2023 Author Share Posted August 31, 2023 Okay, then I'll do it that way. Thanks for your quick reply! Quote Link to comment
extrakaese Posted September 4, 2023 Author Share Posted September 4, 2023 (edited) Restored the data and everything ran smoothly for 2 days, now 32 errors again, last time it was 128. This time I have saved the diagnostics.  I hadn't replaced the cable yet because I don't have a replacement.  Maybe @JorgeB can help me again?  If it's really just the cable, I'll order a new one later to install it tomorrow.  Thanks in advance unraid-diagnostics-20230904-1522.zip Edited September 4, 2023 by extrakaese Quote Link to comment
Solution JorgeB Posted September 4, 2023 Solution Share Posted September 4, 2023 Still looks like a power/connection problem. Quote Link to comment
extrakaese Posted September 4, 2023 Author Share Posted September 4, 2023 Ok, I have a Molex/SATA adapter there, but one of those that are separate and not tight together. Â And the errors came last time and this time, right when the hard drive started from the spindown. Â Is it safe to use such a cable? Because of "Molex to SATA, lose all your data". Â Thanks for the quick reply. Quote Link to comment
JorgeB Posted September 4, 2023 Share Posted September 4, 2023 23 minutes ago, extrakaese said: right when the hard drive started from the spindown. 5 minutes after spin up, so most likely unrelated, but you can disable spin down to see if it helps. Â 24 minutes ago, extrakaese said: Is it safe to use such a cable? I prefer using splitters that only split one plug into two, though for molex can be OK, but IMHO should still be avoided. Â Quote Link to comment
extrakaese Posted September 4, 2023 Author Share Posted September 4, 2023 Ok, thanks, then I look that I find one with two. Â Alternatively, I would take the one with 4, but only plug in 2, should then have the same effect, right? Quote Link to comment
itimpi Posted September 4, 2023 Share Posted September 4, 2023 32 minutes ago, extrakaese said: Ok, I have a Molex/SATA adapter there, but one of those that are separate and not tight together.  And the errors came last time and this time, right when the hard drive started from the spindown.  Is it safe to use such a cable? Because of "Molex to SATA, lose all your data".  Thanks for the quick reply.  I would expect that to be fine because the SATA connectors are all 'crimped' to the power lines.  Quote Link to comment
extrakaese Posted September 4, 2023 Author Share Posted September 4, 2023 Ok, thanks. Apparently it is not so easy to find "crimped" 2-1 in Germany, so now I ordered the 4-1 and will install it tomorrow and connect to only 2 hard drives.  Is there anything else I need to consider?  The harddisk is connected to a HBA controller, so I'll use one of the other SATA connectors, if that's the problem. So it probably can not be something else, just power/connection?  If there are errors again, I'll post it here again.  Thanks for your help Quote Link to comment
itimpi Posted September 4, 2023 Share Posted September 4, 2023 6 minutes ago, extrakaese said: Ok, thanks. Apparently it is not so easy to find "crimped" 2-1 in Germany, so now I ordered the 4-1 and will install it tomorrow and connect to only 2 hard drives. I think with molex on the PSU side you can normally get away with 4-way splitter. Â Â Not something I would want do if the PSU side is SATA as they are not rated for as high a current. Â Quote Link to comment
extrakaese Posted September 4, 2023 Author Share Posted September 4, 2023 40 minutes ago, itimpi said: Not something I would want do if the PSU side is SATA as they are not rated for as high a current.  Sorry, don't quite understand what you mean by that? I don't understand that much about these things so far. Am still relatively new to these things. 😕 Quote Link to comment
itimpi Posted September 4, 2023 Share Posted September 4, 2023 2 minutes ago, extrakaese said: Sorry, don't quite understand what you mean by that? I don't understand that much about these things so far. Am still relatively new to these things. 😕 SATA -> SATA splitter cables are available but I would never split a SATA cable more than 2 ways although I would be happy with splitting a molex -> SATA cable 4 ways. 1 Quote Link to comment
extrakaese Posted September 4, 2023 Author Share Posted September 4, 2023 Ahhh, now I understand. Did not know that there are also SATA splitters.  Then I'm on the safe side with the Molex-SATA.  Thanks for the explanation Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.