paulmorabi Posted October 4, 2023 Share Posted October 4, 2023 My Unraid server has been freezing randomly over the last few days. I've enabled syslog and the last lines recorded before the system freezing are: Quote Oct 4 02:10:04 FatBoy kernel: PMS LoudnessCmd[17642]: segfault at 0 ip 00001513356b3920 sp 00001513301180c8 error 4 in libswresample.so.4[1513356ab000+18000] l ikely on CPU 0 (core 0, socket 0) Oct 4 02:10:04 FatBoy kernel: Code: cc cc cc cc cc cc cc cc cc cc 8d 04 49 48 98 4d 89 c1 49 29 c1 48 63 c2 48 63 c9 49 39 f9 76 7c 66 2e 0f 1f 84 00 00 00 00 00 <f3> 0f 10 06 f3 0f 5a c0 f2 0f 11 07 f3 0f 10 04 06 48 01 c6 f3 0f I'm running Plex via docker on the server with GPU pass through via an NVidia card. I've updated Plex recently also upgraded to 6.12.4. However, on the latter, the first crash happened prior to that. I've attached diagnostics and prior to this happening over the last few days had months of stability without any issues with the same setup. Any help would be appreciated. fatboy-diagnostics-20231004-0817.zip Quote Link to comment
JorgeB Posted October 4, 2023 Share Posted October 4, 2023 2 hours ago, paulmorabi said: PMS LoudnessCmd[17642]: segfault This should be harmless, used to see them in a lot of diags. 2 hours ago, paulmorabi said: I've enabled syslog Post the complete log file. Quote Link to comment
paulmorabi Posted October 4, 2023 Author Share Posted October 4, 2023 1 minute ago, JorgeB said: This should be harmless, used to see them in a lot of diags. Post the complete log file. Here you go. There is not much additional there. I thought it was linked to the plex issue as the following kernel message is logged at the same second. syslog-192.168.1.66.log Quote Link to comment
JorgeB Posted October 4, 2023 Share Posted October 4, 2023 3 minutes ago, paulmorabi said: There is not much additional there. Yep, could still be Plex related, see if it crashes if you leave it disabled. Quote Link to comment
paulmorabi Posted October 4, 2023 Author Share Posted October 4, 2023 1 hour ago, JorgeB said: Yep, could still be Plex related, see if it crashes if you leave it disabled. I downgraded to the previous version and will try this and then if it crashes again, disable. Quote Link to comment
paulmorabi Posted October 6, 2023 Author Share Posted October 6, 2023 On 10/4/2023 at 12:02 PM, paulmorabi said: I downgraded to the previous version and will try this and then if it crashes again, disable. Downgraded to the previous version of Plex and thought it was ok but has just happened again. Nothing in the logs beforehand that would indicate anything. syslog attached, any ideas? syslog-192.168.1.66.log Quote Link to comment
JorgeB Posted October 6, 2023 Share Posted October 6, 2023 9 minutes ago, paulmorabi said: Nothing in the logs beforehand that would indicate anything. syslog attached, any ideas? Without anything logged difficult to guess what the problem is, you could try downgrading to v6.11.5 and see if the same thing happens. Quote Link to comment
paulmorabi Posted October 6, 2023 Author Share Posted October 6, 2023 12 minutes ago, JorgeB said: Without anything logged difficult to guess what the problem is, you could try downgrading to v6.11.5 and see if the same thing happens. Why that version? 6.12.3 and all other previous versions were also super stable until this started a few days back (and it was on 6.12.3 when this first happened). Quote Link to comment
JorgeB Posted October 6, 2023 Share Posted October 6, 2023 2 hours ago, paulmorabi said: 6.12.3 and all other previous versions were also super stable until this started a few days back (and it was on 6.12.3 when this first happened). So it was stable with 6.12.3 or not? If the issue started out of the blue with a known good release it could be hardware related, that usually does not leave anything logged. Quote Link to comment
paulmorabi Posted October 7, 2023 Author Share Posted October 7, 2023 15 hours ago, JorgeB said: So it was stable with 6.12.3 or not? If the issue started out of the blue with a known good release it could be hardware related, that usually does not leave anything logged. Yes, it started out of the blue last Sunday. The only thing I did prior to that was update Plex. And one week before that, edit some of the CPU pinning and isolation settings for my docker and VM. Quote Link to comment
JorgeB Posted October 7, 2023 Share Posted October 7, 2023 Try with Plex disabled, if it still crashes it's likely hardware, if not Plex would be the likeky problem. Quote Link to comment
paulmorabi Posted October 7, 2023 Author Share Posted October 7, 2023 (edited) 1 hour ago, JorgeB said: Try with Plex disabled, if it still crashes it's likely hardware, if not Plex would be the likeky problem. I've updated the BIOS and edited the BIOS settings to: * Disable C states * Set power supply idle control to typical current * disabled all over clocking and XMP profile. * disabled CPPC preferred cores and CPPC I noticed these were mentioned elsewhere as affecting stability especially on older Ryzen's. However, they've never caused issues before here. I also removed a USB card I no longer use and given it a general dusting inside. High temperature doesn't seem to be an issue though. The Plex error and the kernel code error occurred again overnight and it only froze an hour or so ago so probably not that either. If it crashes again, I'll revert the BIOS settings and disable all dockers, including Plex, and probably also the VM I have running. If it stays up more than 48 hours then the problem is somewhere there and I need to gradually enable things until it freezes again? I can also restore from a backup I took about ~2 months ago. If it's hardware, where do you recommend I start? Edited October 7, 2023 by paulmorabi Quote Link to comment
JorgeB Posted October 7, 2023 Share Posted October 7, 2023 3 minutes ago, paulmorabi said: If it's hardware, where do you recommend I start? Since you have two sticks of RAM, try with just one, if the same try the other one, that would basically rule out bad RAM. Quote Link to comment
paulmorabi Posted October 8, 2023 Author Share Posted October 8, 2023 22 hours ago, JorgeB said: Since you have two sticks of RAM, try with just one, if the same try the other one, that would basically rule out bad RAM. OK, had another crash with all of those BIOS changes so reverted the settings and took a stick of memory out. Will alternate if it happens again. I'm guessing its unlikely both suddenly became faulty so if its happening with both sticks then its somewhere else? Quote Link to comment
JorgeB Posted October 8, 2023 Share Posted October 8, 2023 11 minutes ago, paulmorabi said: so if its happening with both sticks then its somewhere else? Most likely, it would very bad luck to have 2 bad sticks, but of course not impossible. Quote Link to comment
paulmorabi Posted October 16, 2023 Author Share Posted October 16, 2023 On 10/8/2023 at 12:35 PM, JorgeB said: Most likely, it would very bad luck to have 2 bad sticks, but of course not impossible. Last Sunday, I removed a stick of RAM and reseated the CPU heatsink and cleaned a few other areas. I don't want to jinx myself but its been 7 days and no system freezes as yet. Looks like it is probably RAM gone bad and/or cleaning/reseating a few things has fixed it? Either way, I'll give it a couple more days and purchase replacement RAM. On RAM, is there anything I should look out for when it comes to purchasing? Given this will run 24/7, apart from ECC, anything I need to consider? Quote Link to comment
Solution paulmorabi Posted November 12, 2023 Author Solution Share Posted November 12, 2023 On 10/16/2023 at 8:37 AM, paulmorabi said: Last Sunday, I removed a stick of RAM and reseated the CPU heatsink and cleaned a few other areas. I don't want to jinx myself but its been 7 days and no system freezes as yet. Looks like it is probably RAM gone bad and/or cleaning/reseating a few things has fixed it? Either way, I'll give it a couple more days and purchase replacement RAM. On RAM, is there anything I should look out for when it comes to purchasing? Given this will run 24/7, apart from ECC, anything I need to consider? Crashes stopped after this and I replaced the RAM so seems like it was a faulty RAM stick. Quote Link to comment
poloconway Posted December 30, 2023 Share Posted December 30, 2023 Running 6.12.6, add second solid state drive for cash setup with other 1 tb solid id s raid mirror. 14tb parity. 2 14tb array drives and 1 4tb drive. Been at this for a week now, I have changed setting, bios, removing plugs updated plugin. At this point I have no close what to do. Cache are set to zfs. Have plex,sab, radarrm sonarr, Home assist, I ran the last time with plex just going and in about 30 min, server frozen beaning I have to force power down and reboot. I get something is wrong in docket or its my plex configurations conwayserver-diagnostics-20231229-0817.zip Quote Link to comment
JorgeB Posted December 30, 2023 Share Posted December 30, 2023 Enable the syslog server and post that after a crash. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.