dansonamission

Thanks for the info, that is good to know. Its tempting to purchase another 9207 and see if it works.

Looking at the H220 card again, there's a sticker that says SAS9205-8i H3-25278-05D and under the HP sticker logo is the LSI silk screen.

It was fitted with this..... Sticker on it says HP 220 0a:00.0 Serial Attached SCSI controller [0107]: Broadcom / LSI SAS2308 PCI-Express Fusion-MPT SAS-2 [1000:0087] (rev 05) DeviceName: Storage Controller Subsystem: Broadcom / LSI 9207-8i SAS2.1 HBA [1000:3020] Kernel driver in use: mpt3sas Kernel modules: mpt3sas Now fitted with..... LSI branded 07:00.0 Serial Attached SCSI controller [0107]: Broadcom / LSI SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] [1000:0072] (rev 03) Subsystem: IBM SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] [1014:03cb] Kernel driver in use: mpt3sas Kernel modules: mpt3sas

I've installed a different LSI card today and the update is working ok. Is there a list of supported cards anywhere?

Thanks, thought that might be the case.

After some more reboots i got it back on the gui, but have lost all my drives.

My controller running the sea gate drives reports as follows Serial Attached SCSI controller: Broadcom / LSI SAS2308 PCI-Express Fusion-MPT SAS-2 (rev 05)

I thought I had saved them, but it would seem not, sorry. The server has been restored to 6.8.3 already, when I have more time on the weekend I will run the update again. I was only wanted to try out the cache drive pool with the different formatting. With the samsung drives I have, with more than one disk in the pool, its really slow.

I just updated to 6.9beta30 from 6.8.3 and none of my drives have been found on a HP H220 LSI 9205-8i 9207 with P20 firmware. It took a really long time to boot as well. The card is detected but no drives.

I removed the plugin earlier. The drive is a ST4000NM0023 Seagate, revision GS0D and the card HP H220 LSI 9205-8i 9207 with P20 firmware.

I've just installed this plugin on 6.8.3 Clicked the green dot to spin a drive down and now the drive is disabled and I dont seem to be able to get it back! Oct 6 13:23:00 Apollo emhttpd: error: mdcmd, 2723: Input/output error (5): write Oct 6 13:23:00 Apollo kernel: mdcmd (48): spindown 3 Oct 6 13:23:00 Apollo kernel: md: do_drive_cmd: disk3: ATA_OP e0 ioctl error: -5 Oct 6 13:23:01 Apollo SAS Assist v0.6[47280]: spinning down slot 3, device /dev/sdb (/dev/sg1) Oct 6 13:23:17 Apollo kernel: sd 7:0:0:0: [sdb] tag#3684 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Oct 6 13:23:17 Apollo kernel: sd 7:0:0:0: [sdb] tag#3684 Sense Key : 0x2 [current] [descriptor] Oct 6 13:23:17 Apollo kernel: sd 7:0:0:0: [sdb] tag#3684 ASC=0x4 ASCQ=0x11 Oct 6 13:23:17 Apollo kernel: sd 7:0:0:0: [sdb] tag#3684 CDB: opcode=0x88 88 00 00 00 00 00 e9 07 bc 20 00 00 00 18 00 00 Oct 6 13:23:17 Apollo kernel: print_req_error: I/O error, dev sdb, sector 3909598240 Oct 6 13:23:17 Apollo kernel: md: disk3 read error, sector=3909598176 Oct 6 13:23:17 Apollo kernel: md: disk3 read error, sector=3909598184 Oct 6 13:23:17 Apollo kernel: md: disk3 read error, sector=3909598192 Oct 6 13:23:17 Apollo kernel: sd 7:0:0:0: [sdb] tag#3686 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Oct 6 13:23:17 Apollo kernel: sd 7:0:0:0: [sdb] tag#3686 Sense Key : 0x2 [current] [descriptor] Oct 6 13:23:17 Apollo kernel: sd 7:0:0:0: [sdb] tag#3686 ASC=0x4 ASCQ=0x11 Oct 6 13:23:17 Apollo kernel: sd 7:0:0:0: [sdb] tag#3686 CDB: opcode=0x8a 8a 00 00 00 00 00 e9 07 bc 20 00 00 00 18 00 00 Oct 6 13:23:17 Apollo kernel: print_req_error: I/O error, dev sdb, sector 3909598240 Oct 6 13:23:17 Apollo kernel: md: disk3 write error, sector=3909598176 Oct 6 13:23:17 Apollo kernel: md: disk3 write error, sector=3909598184 Oct 6 13:23:17 Apollo kernel: md: disk3 write error, sector=3909598192 Oct 6 13:24:15 Apollo kernel: mdcmd (49): spindown 3 Oct 6 13:24:15 Apollo kernel: md: do_drive_cmd: disk3: ATA_OP e0 ioctl error: -5 Oct 6 13:24:15 Apollo emhttpd: error: mdcmd, 2723: Input/output error (5): write Oct 6 13:24:15 Apollo SAS Assist v0.6[47679]: spinning down slot 3, device /dev/sdb (/dev/sg1)

Thanks guys, the re-install option let us do what we needed to do.

Hi, How can we install multiple dockers from the same template? I have a Pi hole installed and would like to install another one. The only option i can see on the apps pages is to edit the existing one. Thanks

Hanging on ..... How long before it becomes an RC? I’m not running betas and only 5 days left of the trial on this system. If I can format via command then great as will know straight away if it has worked.