NMGMarques

Either my search was really bad or I couldn't find the answer. I got metube up and running: It grabs and downloads the files I need. But then I can't play them back. Clicking them just gives me an error: Where am I going wrong?

Has anyone figured out a solution?

I have tried all I can think of. Admittedly, not much, since I am no expert. The best I can get is to get the machine to refuse my connection, but nothing more. Anyone have any tips?

Are Office documents not supported? Trying to upload any Office docs gives me a File type application/vnd.openxmlformats-officedocument.spreadsheetml.sheet not supported or similar error, depending on filetype. This particular one was an Excel file.

I checked the file, but I can't find a line that mentioned that port combination. I find a lot of references to ports all over the file, but not "ranged" like that. Do I need to change every instance of a port present in the file?

Was following a video off of YouTube. Truly the most asinine mistake I could make. Thanks for pointing it out.

Hi all. Hoping someone can help me figure out what is wrong. I can't get paperless to start. 1 - Installed Redis. Seems to be up and running. 2 - Installed paperless-ngx (Selfhosters version). I get no errors either during install or after making a change and hitting DONE. The paths are good and valid. However, whenever I start paperless, it says started but as soon as I refresh the Docker Containers page, it is back to stopped. This is what I get if i click paperless LOGS: Any ideas? What information do you need me to post and where can I grab it? I'll gladly provide as much details as I can.

I don't know if I did it right or not. There is a lot of difference between the files for me to think I may have messed up somewhere. The two log files, for latest and also for the working version. I stopped the container, deleted existing log files, started the container and opened the webui. Then I stopped the container, renamed the log file, switched to latest, started the container and tried to open the UI getting the error again. Stopped the container and renamed the log file. 1.7.4.3769-1-01_supervisord.log latest_supervisord.log

I'm about as skilled at web apps and coding as a potato. So I guess I'll be stuck on this version until someone posts a fixed version.

For some reason, the docker seems to be running, though I can't access it using the http://localip:9696 address or even https://localip:9696. And when I try from one of the web apps to connect to it, it isn't working now, either. What info do I need to post to help troubleshoot? PS: tried rolling back to a version from 6 days ago. PS2: So on a whim, I rolled back even further and it started to work again. Seems that the current or latest version is not working, at least for me. Any ideas on what might be the issue are welcome.

Just in case someone stumbles onto this topic, this solved it for me. I was missing the reboot after the nvidia drivers install.

What about just replacing the cache drive with a larger one? Is that doable? What would it entail?

Does that mean I’ll have to reconfigure everything? Or will my settings all be retained?

Same here. However, yes, the docker file seems to be taking up the 107 gigs. Curious for me is that when I went to the Docker tab to figure out the culprit, I only see 19 gigs being used.

Upped. biggekko-ur-diagnostics-20230513-2234.zip

So I keep having issues and I noticed that system share is taking up close to all of my 120gb cache drive. Triggering the mover does nothing. If I change my appdata out of the cache to the data drives, I get a lot of errors, too, so I can’t afford to have all the space used by system, nor do I understand why system uses up so much. I have been told in the past that I should keep system on cache, but this is now becoming unbearable. Any suggestions?

Whatever I try, I can't seem to bypass the 5.5gb limit. I tried setting unlimited, increasing to 10 GB, even 200 GB. In the end, I always get these 2 contracting results and my cell phone will not upload past the 5.5gb.

Hi all. I have an existing unRAID server with a key I purchased some years ago. Over time, I have set it up the way I like. Also over time, I have devoted more and more of my server to business use. This, to the point the server is now mostly business-centric. Today, I took possession of new hardware. The idea is to buy a new unRAID key to use on this machine. The idea is to finally separate work and business. My plan is to use the current setup as the business side server. The new hardware will become my personal rig. Here is the caveat: although the existing rig will remain, I need to remove the key from that rig to the new one. Why? Because I will purchase the new key for the company and it will therefore be registered as such, while the existing key which is registered to me as a personal user, will move over to the new rig. So the question is, how do I achieve this with as little stress as possible? I need to create a new server, somehow move my personal stuff over to the new server, then move then swap the keys somehow. Suggestions? Edit: The new hardware has larger drives. So I plan on using those. Therefore, I can't just move the key and the drives.

I'm stuck right at the very start. My server's home IP address is 192.168.1.10 and I access the server from most of my devices using a WireGuard VPN tunnel to IP 10.253.0.1. What IP do I need to give this docker to make it work? Leaving it at the default, the web ui tries to default do 192.168.1.1 which I can't access over the VPN. And if I try to access it using 10.253.0.1:443 or 80, just brings me to my unRAID instance, naturally.

Then I can assume that it really is disk2 and that there is no relevant data in the device?

I'm assuming it's disk2 in your example. I typed in ls-alh /mnt/disk2 and in return got this: but when listing drives with the below command it only shows 1 disk it seems.

You mean remove the disk and then while it gives me the error do the re-sync? And how can I see what data is on it? It says it has 400MB of data, though when I click the small explorer icon to the right, it shows an empty drive.

So yeah... I had 2x 4TB drives, one as parity and one as data. 1x 120GB SSD as cache (if I had known, I'd have made it a larger drive). I was trying to add a 64GB usb thumb drive to the system to backup the current USB boot thumb drive. Make it a clone, so to speak, to have a backup. Seems I managed to add it to the array. Now I can't stop and remove the disk from the array since it always shows up as missing with data to be reconstructed. So I added it back for now. How can I clear the USB drive and prepare it for permanent removal? I am hoping to create a new array of 3x 1TB disks (1x parity and 2x data... not sure if can be done) and need that extra slot now being used in the OS by that USB drive.

I know I can play the game in offline mode, though I can't find any reference in this thread as to how to put the server in offline mode.

What am I missing? I am trying to connect to the server using 1.18.1. [17:24:46] [Server thread/INFO]: /10.253.0.5:60477 lost connection: Failed to verify username!