Keanu

Issue resolved. I reslotted the device (Drive caddy) and shut down / restarted the device and it showed up. Phew. Thank you for your quick reply, I really really appreciate it. Lesson learnt, always check your drive connections before posting. Was just in a bit of a panic! Thank you again, please consider this issue resolved! Kind regards,

Hi Itimpi, Thank you for the quick response! Please see attached the diagnostics. I also added a little bit more info to the initial post regarding the drive. Thanks again, Kind regards,

Hi all, My parity drive failed, thought it may have just been unraid messing up as it'd been on for over a year, so I stopped the array, rebooted the server and the failed drive disappeared from the array device list - fine, no problem, I've got a drive to replace it with (Not a new drive, one from another server with minimal use) I've whacked the new drive in, but it's not showing up on the dropdown for "Identification" so I can select it as a parity drive? I've read somewhere about the "New Config", but I'm worried to proceed because it states "This is a utility to reset the array disk configuration so that all disks appear as "New" disks, as if it were a fresh new server." and it makes me think that it'll make me format all the drives to proceed - which is obviously bad as data loss. Been following along with this: https://wiki.unraid.net/The_parity_swap_procedure but I'm stuck on step 3. Edit: Just for extra info, i've checked the system devices and it's showing up as the following: "[1:0:0:0]disk ATA WDC WD30EFRX-68E 0A82 /dev/sdb -" Any help would be greatly appreciated. Thanks, Kind regards,

Hi there, I'm having an issue with hooking Lidarr up to NZBHydra. Not entirely sure why but it just seems to be timing out? This is all I get from the logs; [Info] RssSyncService: Starting RSS Sync [Warn] FetchAndParseRssService: No available indexers. check your configuration. [Info] DownloadDecisionMaker: No results found [Info] RssSyncService: RSS Sync Completed. Reports found: 0, Reports grabbed: 0 [Warn] Newznab: Unable to connect to indexer [v0.4.0.540] System.Net.WebException: The operation has timed out.: 'http://192.168.1.100:5076/api?t=search&cat=3000,3010,3020,3030,3040&extended=1&apikey=<MYAPIKEY>&offset=0&limit=100' ---> System.Net.WebException: The operation has timed out. at System.Net.HttpWebRequest+<RunWithTimeoutWorker>d__244`1[T].MoveNext () [0x000c5] in <b3d41b23de534128a4f18a6e1312f79c>:0 --- End of stack trace from previous location where exception was thrown --- at System.Net.HttpWebRequest.GetResponse () [0x00016] in <b3d41b23de534128a4f18a6e1312f79c>:0 at NzbDrone.Common.Http.Dispatchers.ManagedHttpDispatcher.GetResponse (NzbDrone.Common.Http.HttpRequest request, System.Net.CookieContainer cookies) [0x000f6] in C:\projects\lidarr\src\NzbDrone.Common\Http\Dispatchers\ManagedHttpDispatcher.cs:64 --- End of inner exception stack trace --- at NzbDrone.Common.Http.Dispatchers.ManagedHttpDispatcher.GetResponse (NzbDrone.Common.Http.HttpRequest request, System.Net.CookieContainer cookies) [0x001a3] in C:\projects\lidarr\src\NzbDrone.Common\Http\Dispatchers\ManagedHttpDispatcher.cs:92 at NzbDrone.Common.Http.Dispatchers.FallbackHttpDispatcher.GetResponse (NzbDrone.Common.Http.HttpRequest request, System.Net.CookieContainer cookies) [0x000b5] in C:\projects\lidarr\src\NzbDrone.Common\Http\Dispatchers\FallbackHttpDispatcher.cs:53 at NzbDrone.Common.Http.HttpClient.ExecuteRequest (NzbDrone.Common.Http.HttpRequest request, System.Net.CookieContainer cookieContainer) [0x0007e] in C:\projects\lidarr\src\NzbDrone.Common\Http\HttpClient.cs:121 at NzbDrone.Common.Http.HttpClient.Execute (NzbDrone.Common.Http.HttpRequest request) [0x00008] in C:\projects\lidarr\src\NzbDrone.Common\Http\HttpClient.cs:57 at NzbDrone.Core.Indexers.HttpIndexerBase`1[TSettings].FetchIndexerResponse (NzbDrone.Core.Indexers.IndexerRequest request) [0x0004b] in C:\projects\lidarr\src\NzbDrone.Core\Indexers\HttpIndexerBase.cs:282 at NzbDrone.Core.Indexers.HttpIndexerBase`1[TSettings].FetchPage (NzbDrone.Core.Indexers.IndexerRequest request, NzbDrone.Core.Indexers.IParseIndexerResponse parser) [0x00000] in C:\projects\lidarr\src\NzbDrone.Core\Indexers\HttpIndexerBase.cs:259 at NzbDrone.Core.Indexers.HttpIndexerBase`1[TSettings].TestConnection () [0x0000e] in C:\projects\lidarr\src\NzbDrone.Core\Indexers\HttpIndexerBase.cs:296 [Warn] LidarrErrorPipeline: Invalid request Validation failed: -- Unable to connect to indexer, check the log for more details Any help would be appreciated! I've installed ping onto the container, and can confirm that I can ping the ip 192.168.1.100 Thanks,

Been having with domain name resolution, and it not connecting to anything. Not sure if anyone else has been having this issue, however the /etc/resolv.conf had a dns ip of 127.0.0.11, if you vi into it, you can change it. Hopefully this helps someone!

Derp. I should really learn to read before asking questions.... Apologies for wasting your time again! Thanks for the help again. Pretty sure that was my last issue! (I hope!) Thanks again, -Keanu

Have it so Internal machines are allowed to talk to eachother on pfsense, and set under advanced settings on headphones. Yep, Musicbrainz has completed, all booted, even sorted the CSS. Thanks, -Keanu

Hi Again CHBMB, Apologies! Didn't think! Both the Headphones container and Musicbrainz container are located on the same server, however headphones is using it's own IP rather than bridging (For routing through VPN on PFSense) - Guide found here: So Headphones uses 192.168.1.130:8181, musicbrainz uses 192.168.1.100:5000. Headphones currently uses the musicbrainz.org site, but want to swap it over to local for speed. Hopefully that covers everything, let me know if there's any other info you might need and i'll get it to ya! Thanks, -Keanu

Hi there, Having an issue with Musicbrainz and Headphones - I've set the musicbrainz settings under "Advanced Settings" in headphones, but whenever I search, I get this error: Any help would be appreciated! Thanks, -Keanu

Annnnnnnnnnnnnd i'm an idiot. Thanks for your help. Issue was that the shares on the other server were set on NFS to "Secure". Problem was, apparantly it didn't ask me for a username and password for them, but it did the other day? So could potentially be an issue with Unassigned Devices or something. Not sure. But yeah, thank you for your quick replies and helping me find a solution, greatly appreciate it!

just changed it back to Read/Write, but still the same output "touch: cannot touch '/tv/testfile': Read-only file system" I'm not entirely sure why though! Bit of an update though, i've just tried that on another container, same issue, so it isn't localised to Sonarr, however other containers aren't showing any errors.. So, that's odd! I've got a few more ideas now though, thank you for your help! I'll update here once I know what the issue is, incase anyone out there is potentially having the same issue as me. Thanks, -Keanu

touch: cannot touch '/tv/testfile': Read-only file system Just as a quick side note, I have got the "Access Mode" on the Host Path set to "RW/Slave" (Read somewhere to do that!)

Hi CHBMB, Thanks for the quick replies! Output below; Thanks, -Keanu

Hi CHBMB, I know, bit of an odd setup, i'm building an army of HP Microservers because it's based in a small cupboard! So yeah, essentially, my setup is going to be, or is like this. App Server <-> Storage Server Sonarr <-> Deluge Sonarr <-> Files (I've kept Deluge on the old storage server because else it'll just be pinning the network to it constantly transferring files, etc!) Hopefully that helps clear things up! As said above, i've checked the PID / GID, theres a top level folder called TV, then sub folders called Series, etc, then inside of the series folder, is the shows. Permissions are as below; Top level - TV - 777 Series - 777 TV Show - 775 (That might be it.. Going to check that!) - just checked, not the issue! show.mkv - 775 Not entirely sure what else to check! Thanks, -Keanu

Hi there! I'm having a bit of an odd issue, i've just moved all of my docker containers over to another unraid server, and i've got my original (that used to run Sonarr) sitting just as data storage now. I've hooked up the Media drive using Unassigned devices "NFS" share option, that's all worked fine. Now, when I go into Sonarr and try to "Import Existing Series On Disk", i'm getting the error: "Folder is not writable by user abc" I've checked all the PUID / GUID's (Standard 99 / 100) of the directories of the files, the permissions, etc, but no luck! It should be using exactly the same setup as before, as i'm using the same docker container? I'm at a bit of a loss as to what exactly is stopping it, all it says in the log file is "[Warn] NzbDroneErrorPipeline: Invalid request Validation failed:-- Folder is not writable by user abc" nothing else. What's even odder is the fact that other containers don't seem to have this problem? Any suggestions to fix this would be greatly appreciated. Thanks, -Keanu

Thanks for clearing that up! Will look into the other alternative of porting it through a vpn. Thanks,

Hi there, I'm currently stuck on STATEMENT: ALTER TABLE dbmirror_pendingdata DROP CONSTRAINT "dbmirror_pendingdata_SeqId" CASCADE WARNING: SET TRANSACTION can only be used in transaction blocks WARNING: SET CONSTRAINTS can only be used in transaction blocks I saw above that you said it was getting updates, but I wanted to check whether or not it'd be okay to reboot the server during this time? Or if I should just leave it be? Thanks, Keanu

Thanks for the reply. I've seen online that you can do it using a reverse proxy? I couldn't find anything relating to either Apache or nginx though. I'm not entirely clued up about all of this though. My other alternative is that i've got a tomato router, with a VPN on it and to route that port through.. But.. Stumped on that too! Kind Regards, -Keanu

Hi there, Where would I set some sort of proxy information for this please? I've got a proxy server running on 8118, but no idea how to attach headphones to it! Thanks, -Keanu

Does this help? and ah okay, I wasn't sure on sizing, so I just set it up as that size a few months ago

Thanks for the quick reply. I've got no idea to be honest. It's located on my cache drive, however I don't *actually* have a cache drive yet, waitin' on it to arrive. I haven't set it up as a share as wasn't sure if I needed to. I thought as much but wasn't entirely sure what information you'd need! Have attached the diagnostics found in there! If theres any other files you need, please let me know. Also, another quick question. What size roughly should the docker image be? I did have a search around a while back but couldn't find a definitive answer, so I set it to about 200GB as I wasn't sure! Thanks! -Keanu homeserv-diagnostics-20160720-1928.zip

Hi there, My apologies if this has already been sorted before, I did search but couldn't find anything relating to my issue. Okay so, whenever I stop the array, and reboot my unraid server, it clears all of the settings for all of my docker containers (essentially, it's exactly the same as the first setup of the container). Is there something that I have to setup to fix / stop this issue? If logs are required, please let me know where to find them and i'll post asap. Looking forward to your reply, Kind Regards, -Keanu