epicurean

Hi, Thank you for your reply. Can I confirm that I should 1) Remove the usb drive and delete the file and folder as stated?

Currently on the latest 6.12.18 version. I put a a larger 12TB drive to replace one of the 8TB data drives in my array. I shut down the array, remove the 8TB drive, and reboot with intention for the 12TB drive to replace the 8TB. However, I keep getting this error, inspite of a few reset/reboots and have been unable to restart. Both the existing 8Tb drive and the 12TB drive at in the machine mv: cannot stat '/usr/local/bin/mover': No such file or directory jq: error: Could not open file /boot/config/plugins/disklocation/dislocation.conf: No such file or directory /tmp/disklocation-install: line 215: [: ==: unary operator expected Highly appreciate any help to remedy this. Thank you!

Thank you !

Will moving the usb flash drive to a different chassis, but same motherboard - will it also recognise which disk drives are allocated for what purpose in the array? What will be best practice before doing something like this? thank you

Thank you Sir! For the mariadb part. do I setup that docker first, or the photoprism first? Appreciate if steps for mariadb (with regards to photoprism) also explained. Thanks again!

Hi everyone, I have failed miserably with many attempts to setup mariadb and photprism on unraid. Are you able to share a step by step guide? assume I am an idiot.

Noted. So I will first need to delete the docker and then reinstall and map exactly like previously?

I should have no issue removing and reinstalling the krusader docker. But i do not wish to lose the data on the plex server docker Is there a way to do so?

Array completed parity check with no errors However, the 2 dockers I have ,binhex-krusader and plex, have a question mark next to it (instead of its usual icon) and I am unable to update it. error says "Configuration not found. Was this container created using this plugin?" How can I fix this?

I dont unfortunately. I got desperate and done this so far: 1) setup a new usb drive for unraid 2) got a new key from the email 3) set new config and put the drive arrays in the order that I remember. (1 parity, 7 drives, 2 x cache pools) 4) unraid says array started and doing a parity sync. 5) I only have 2 dockers (krusader and plex server). Should I just wait for the parity to complete? I seem to see the shares, but they all have an exclamation yellow triangle next to it (except for domains) is there anything else I need to do?

Newbie help needed! the unraid Sandisk USB drive appears to be dead, the bios does not even see it. took it out and put into a pc, and it is also not readable. I have a new usb drive ready. how do I recover my paid Unraid PRO account on this new flash drive?

Sorry to rehash this old thread, but with my 14 core CPU, and I wish to have a much better performance from the plex docker, what do/should I need to do for CPU pinning - if at all. Currently, I get the occasional pause from Plex with error saying the source is not fast enough

New to unraid here. I just installed plex media server, and also created a new ssd pool to put the plex appdata in. how do I transfer the plex appdata to this ssd pool,without losing all my plex history and metadata? Also how do I backup the plex appdata on a regular basis? much thanks for your help

sorry, newbie here. Where can I find the latest docker image of Zoneminder for use in Ubuntu?

Dual gpu to a single vm or two vm's on two gpus? I was testing the latter and it worked fine. For some reason I couldn't run two ovmf bios' though. An ovmf and a seabios combination worked with a 280x video card passed through to each vm running with both vm's running at the same time. Since the 280x requires the crossfire bridge there was no point testing passthrough of both gpu's to the same vm since I can't run crossfire (newer amd cards that don't require the crossfire bridge and perform crossfire over the pcie bus can). Could you share your motherboard bios settings, and also any other ESXI settings on how you run 2 VMs on 2 GPUs? I have an Intel S2600IP4 which I can never get to boot up when I passthrough 2 x AMD 6450 to 2 X windows 10 VMs. Much thanks