Jump to content

Dr_Cox1911

Members
  • Content Count

    43
  • Joined

  • Last visited

Community Reputation

0 Neutral

About Dr_Cox1911

  • Rank
    Advanced Member

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Thank you @johnnie.black for your fast response! Just plugged the HDDs in the onboard controller and see how it goes from now on. Guess sooner or later I will have to invest in a proper HBA controller.
  2. So should I do any preparations before pluggin in the HDDs in a different controller? Or should I just shutdown the server and plug them in another SATA slot (coming from the board controller, not the Marvell controller of course)?
  3. Greetings all, I currently have the problem that some of my HDDs get dropped from the array and are listed in unassigend devices. I thought it might be a SATA-cable problem at first and changed the cables of these HDDs, but the got dropped again. I attached the diagnostics and hope that you guys can shed some light on this. I'm rather scared that my server is dying on me😰 UPDATE: So I just checked my array devices list and the devices are still listed there but also in unassigned list? I attached two screenshots, in those the dropped disks are listed in the array devices list but also in the unassigned devices list with different device identifications (sdX). sirbear-diagnostics-20190912-0821.zip
  4. Hi all, I just set up my first VM in Unraid. It's a Debian VM and I'm now struggling to achieve the datashare between the VM and my Unraid shares. I did read that I can integrate the VM into my normal network and can than access the shares via network just like a normal PC. But isn't there a way that won't integrate my VM in my normal network? I would prefer a way where I can mount a share or a folder on a share directly in the VM and leave the VM itself in it's own network.
  5. Thanks for your help! I shutdown my server, plugged in the USB-stick into my PC and made a backup. After that I deleted the network.cfg. I now have only eth0 listed and everything is working fine. So my case here is closed.
  6. Just tried to change the eth2 to eth0, but even after stopping the array I don't have a section called Interface Rules in Network Settings. Fix Common Problems is now stating, that my DNS settings are borked (this happened since I disabled the onboard NICs).
  7. I disabled both my onboard NICs in UEFI and upon booting into unRaid it states that eth0 can not be found on the console. I'm able to access the webinterface with the eth2 (Intel NIC) though, but in the network settings there is still the eth0 listed. Should I worry about the eth0 not found message during bootup?
  8. I don't want to use the Realtek NICs anymore, but by disabling them in the BIOS won't I lock myself out of the webinterface entirely? And is there another way, because I would have to drag a screen and a keyboard to the server to change this in the BIOS.
  9. Hi all, due to dropped network connections with my Realtek Onboard NIC I decided to install a Intel NIC in my Unraid Server. I'm running Unraid 6.7.2. How can I switch Unraid from using the eth0 (onboard Realtek NIC) to eth2 (I have a second onboard Realtek NIC eth1)? The IP-adress should stay the same (192.168.178.30). I tried to boot up the server with the network cable attached to eth0 and then setting the IP for eth2 to "192.168.178.31". I then plugged the network cable in the eht2 NIC and tried to access the webconfig via 192.168.178.31, but's it's not responding.
  10. Thanks for looking over it, as stated above, I changed the SATA cable. Will look at this drive the next couple of days more carefully and if it acts up again I will post here. Thanks for the ultra fast help ❤️
  11. Thanks for the fast reply! I just checked the cables, couldn't find anything amiss but changed the SATA-cable just to be sure. Booted the server back up and got a dia before and after I started the array. The disk behaves fine right now and I for my noob knowledge the SMART-values don't look that bad. sirbear-diagnostics-20180522-2038_before_Array_start.zip sirbear-diagnostics-20180522-2039_after_Array_start.zip
  12. Greetings, today I received a notification that one of my disks has read errors (13). I wanted to investigate but looking at the smart values, but I can't spin up the drive. The disk log information: May 21 19:59:05 sirbear kernel: sd 9:0:0:0: [sdg] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB) May 21 19:59:05 sirbear kernel: sd 9:0:0:0: [sdg] 4096-byte physical blocks May 21 19:59:05 sirbear kernel: sd 9:0:0:0: [sdg] Write Protect is off May 21 19:59:05 sirbear kernel: sd 9:0:0:0: [sdg] Mode Sense: 00 3a 00 00 May 21 19:59:05 sirbear kernel: sd 9:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA May 21 19:59:05 sirbear kernel: sdg: sdg1 May 21 19:59:05 sirbear kernel: sd 9:0:0:0: [sdg] Attached SCSI removable disk May 21 19:59:15 sirbear emhttpd: WDC_WD40EZRX-00SPEB0_WD-WCC4EPA9UX7P (sdg) 512 7814037168 May 21 19:59:15 sirbear kernel: mdcmd (6): import 5 sdg 64 3907018532 0 WDC_WD40EZRX-00SPEB0_WD-WCC4EPA9UX7P May 21 19:59:15 sirbear kernel: md: import disk5: (sdg) WDC_WD40EZRX-00SPEB0_WD-WCC4EPA9UX7P size: 3907018532 May 21 19:59:17 sirbear emhttpd: shcmd (33): /usr/local/sbin/set_ncq sdg 1 May 21 19:59:17 sirbear root: set_ncq: setting sdg queue_depth to 1 May 21 19:59:17 sirbear emhttpd: shcmd (34): echo 128 > /sys/block/sdg/queue/nr_requests May 21 20:01:17 sirbear emhttpd: shcmd (176): /usr/local/sbin/set_ncq sdg 1 May 21 20:01:17 sirbear emhttpd: shcmd (177): echo 128 > /sys/block/sdg/queue/nr_requests May 22 03:33:07 sirbear kernel: sd 9:0:0:0: [sdg] Stopping disk May 22 03:33:07 sirbear kernel: sd 9:0:0:0: [sdg] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=0x00 The strange thing: the unRaid webGui shows the disk as spun up in the Main and Dashboard view, but when I click on the disk to get to the SMART values it says the disk must be spun up. I also attached my diagnostics, but the SMART for the disk sdg isn't present. sirbear-diagnostics-20180522-2006.zip
  13. Jukebox (playing the sound locally on the machine where airsonic is running) doesn't work for me. If I configure the jukebox player and start a song I get this error in the log: Error in jukebox: java.lang.IllegalArgumentException: No line matching interface SourceDataLine supporting format PCM_SIGNED 44100.0 Hz, 16bit, stereo, 4 bytes/frame, big-endian is supported
  14. Is this on per default? So right after I update my server IP will be added to the LimeTech DNS? If so, any way to alter this to the local, self-signed cert right away and don't add it to the DNS?
  15. Is it possible to don't do this? I'm not a fan of that at all and I really don't need the ability to access my unRaid server across the internet.