September 11, 20214 yr Author Appreciate it ST2000DMZ08 Segate 2TB Sorry missed the rerquest for log tower-diagnostics-20210910-2054.zip Edited September 11, 20214 yr by snuffy47
September 11, 20214 yr Community Expert 2 hours ago, snuffy47 said: Watching the drive I am very unsure why this is so high - its what the old drive indicated as a failure mode but the new drive is not flagging anything Seagate uses that SMART attribute differently than WD. No need to monitor it on Seagate. Nothing to worry about, and no errors being logged so far on rebuild
September 11, 20214 yr Community Expert 4 hours ago, snuffy47 said: Well things are rebuilding..... Watching the drive I am very unsure why this is so high - its what the old drive indicated as a failure mode but the new drive is not flagging anything # ATTRIBUTE NAME FLAG VALUE WORST THRESHOLD TYPE UPDATED FAILED RAW VALUE 1 Raw read error rate 0x000f 079 076 006 Pre-fail Always Never 74902826 That is perfectly normal for some drives where that field is a bit-dependent field so the raw value is difficult to interpret and can effectively be ignored.
September 11, 20214 yr Author Still easily 7 hours to go Been watching this thing like a hawk as it my first cherry on suspected failure and on top of that possible more at risk HD failures I need to call it a night I posted my log just for poops and giggles but will say I miss the ignore and no problems that has been the norm on my end Really appreciate the help on here. I implement every suggestion from my past problems just not experienced enough to understand the warnings Also want to add I have a replacement for disk 1 but I am struggling with replacing it as it is one of the newest drives in my array and damn its 8TB - will say less then 1 year old - that might be putting the cart before the mule but damn it hurts tower-diagnostics-20210911-0031.zip Edited September 11, 20214 yr by snuffy47
September 12, 20214 yr Author Well first drive replaced Now I am not sure which one to replace or if I should wait just happy the rebuild went okay tower-diagnostics-20210911-2131.zip
September 12, 20214 yr Community Expert 1 hour ago, snuffy47 said: not sure which one to replace Do you have SMART warnings for any disks on the Dashboard page?
September 12, 20214 yr Author I started that last night but forgot to shut spin down off. Will do an extended test on all remaining drives and post - though it will likely take a day
September 13, 20214 yr Author Extended test on remaining drives attached D1 tower-smart-20210913-0759.zip D2 tower-smart-20210913-0758.zip D4 tower-smart-20210913-0758.zip D5 tower-smart-20210913-0758.zip D6 tower-smart-20210913-0758.zip D7 tower-smart-20210913-0758.zip D8 tower-smart-20210913-0757.zip
September 14, 20214 yr Community Expert Much simpler for everyone if you just post diagnostics, which contains SMART report for all attached disks.
September 15, 20214 yr Community Expert On 9/11/2021 at 12:38 AM, snuffy47 said: a replacement for disk 1 but I am struggling with replacing it as it is one of the newest drives in my array and damn its 8TB - will say less then 1 year old Power on hours puts it at over 2 years old but doesn't seem to be anything wrong with it. Or any of those others. You might just keep the new disk as a spare.
September 18, 20214 yr Author Okie Dokie I still have a thumbs down on Disk 1 and before I had the crazy Disk 3 failure we were targeting Disk 2. Attached the display of disk 1. If I was ignoring things in the past need to understand better what I can acknowledge and what I should be proactive about. Alot of the 2GB are older for sure Really appreciate all the help
September 18, 20214 yr Community Expert I can only guess that I was looking at some other diagnostics when I said On 9/14/2021 at 10:57 PM, trurl said: Power on hours puts it at over 2 years old but doesn't seem to be anything wrong with it. Or any of those others. You might just keep the new disk as a spare. Post new diagnostics
September 18, 20214 yr Author Disk 1 is rebuilding fingers crossed sad to see the 8TB go bye bye I posted my Disk 2 GUI for thoughts - I have drives now to replace it The other disks in the GUI have no orange lines except 2 with UDMA CRC error count 30 and 21. Edited September 18, 20214 yr by snuffy47
September 18, 20214 yr Community Expert The pending sector on disk2 I hope doesn't cause problems for disk1 rebuild. I had a rebuild going when another disk suddenly got a lot more than that but it didn't seem to cause any problems. Disk2 might even be OK to continue to use if you could get it to reallocate that pending sector. After disk1 rebuilds you could try to rebuild disk2 to itself, which should make it reallocate the pending sector and so change it to a reallocated sector, and a single reallocated sector isn't very concerning as long as it doesn't increase, since disks have extra sectors just for that purpose. The large number of reallocated on disk1 is more than I would want in my array though and a reason to replace.
September 18, 20214 yr Author Quote The pending sector on disk2 I hope doesn't cause problems for disk1 rebuild. Me too 19hrs and we will know The items like the Pending Sector amount is there a Ok - Not ok but change very soon number that I can use to ensure I donnt get intot this agian Or I guess I am really asking when there is orange lines - When do I pull the trigger to replace though will likely be a moving target just looking for a best recommendation - lets say not critical data Not saving baby monkeys here - I do have critical data though hahaha Edited September 18, 20214 yr by snuffy47
September 19, 20214 yr Author Event: Unraid Parity sync / Data rebuild Subject: Notice [TOWER] - Parity sync / Data rebuild finished (0 errors) Description: Duration: 20 hours, 55 minutes, 4 seconds. Average speed: 106.3 MB/s Importance: normal Will try what you suggested for Disk 2 now
September 19, 20214 yr Community Expert 23 minutes ago, snuffy47 said: replace Disk 2 You could run preclear on the original that should get its pending sector reallocated.
September 20, 20214 yr Author I plan to do something the 8TB and 2TB wasnt sure what but will preclear and see what happens Event: Unraid Parity check Subject: Notice [TOWER] - Parity check finished (0 errors) Description: Duration: 19 hours, 51 minutes, 6 seconds. Average speed: 112.0 MB/s Importance: normal The other 2 with UDMA CRC error count 30 and 21 will monitor Well it was a mess but with your help trurl and the UNRAID community looks like I am back to a healthy status
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.