May 30, 20224 yr Hello, I have a Dell PowerEdge T420 Server.. i have never experienced any problems when upgrading before, but when i Upgrade from 6.10.1 to 6.10.2 the interface will not load.. i cant access the server from the browser.. and the only way to fix it is to boot in GUI with safe mode and rollback to 6.10.1 I have tried many times and have even uninstalled any unnecessary plugins and dockers? could someone give me some insight please. Thanks Ryan
May 30, 20224 yr Community Expert From the release notes: There are number of the Dell Server products that use this NIC driver. You get the diagnostics file by using console monitor and key board. After logging in type at the command prompt: diagnostics That will write the file in the /logs directory on the boot drive. You can shut the server down with a quick push of the Power Button. Look in the ethtool.txt file in the /system folder and see if the OS installed a driver of eth0.
May 30, 20224 yr Author 10 minutes ago, Frank1940 said: From the release notes: There are number of the Dell Server products that use this NIC driver. You get the diagnostics file by using console monitor and key board. After logging in type at the command prompt: diagnostics That will write the file in the /logs directory on the boot drive. You can shut the server down with a quick push of the Power Button. Look in the ethtool.txt file in the /system folder and see if the OS installed a driver of eth0. should this be done before or after the upgrade.. and what if the OS did not install the eth0 driver?
May 30, 20224 yr Community Expert See this post and the next one in the thread: https://forums.unraid.net/topic/124108-unraid-os-version-6102-available/#comment-1132035
May 30, 20224 yr I have faced same problem of my server (Dell R730XD) Error : Device "eth0" does not exist. Cannot find device "eth0"
May 30, 20224 yr Author on my T420 I just went into the bios and changed virutliztion tech to disable and it fix the problem.. 6.10.2 booted,
May 30, 20224 yr My Problem is solved Reboot the server During boot up press F2 to enter the Bios. After open the Bios, enter the menu System Bios -> Processor Settings -> Virtualization Technology Set it to disabled Press Esc to get to the top menu again Press F10 to exit the bios and save The server should now boot again as normal, Then Upgrade Unraid OS from 6.10.1 To 6.10.2 without (Cannot find device "eth0") problem.
May 30, 20224 yr 14 hours ago, Nishadul Haque said: My Problem is solved Reboot the server During boot up press F2 to enter the Bios. After open the Bios, enter the menu System Bios -> Processor Settings -> Virtualization Technology Set it to disabled Press Esc to get to the top menu again Press F10 to exit the bios and save The server should now boot again as normal, Then Upgrade Unraid OS from 6.10.1 To 6.10.2 without (Cannot find device "eth0") problem. Works for me to, but can you run VMs now?
May 30, 20224 yr 4 hours ago, Flemming said: Works for me to, but can you run VMs now? Ran into this issue on my Dell r720, but not the r710. Disabling virtualization allows the system to boot, and everything appears normal, but VMs refuse to start. I’m assuming we need to wait until there’s an UnRAID fix and its not as simple as a configuration change? Regardless, thanks for all the help this forum affords.
May 30, 20224 yr Author So with virtualization disabled my virtual machines don’t work what’s the workaround for this
May 31, 20224 yr Community Expert All indications so far are that Dell servers can run with vt-d enable without issues, to do that see here: https://forums.unraid.net/bug-reports/stable-releases/after-i-upgraded-to-6102-my-network-interfaces-dissappeared-r1956/?do=findComment&comment=19584
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.