RussellG Posted September 8, 2022 Share Posted September 8, 2022 (edited) Ok, so I had a crazy AC leak and two of my three drives got wet and the PCBs fried. I had one parity, but two drives failed. I have since repaired one of the two bad drives (swapped ROM IC to a new donor board) and want to rebuild parity, but unraid has forgotten one of the disks. Before I go any further and bring confusion, I am going to start with my disks and their status 10Tb Parity - Good and healthy 10Tb Disk1 - Repaired and appears to be fine, but unRAID doesn't "remember" it? 10Tb Disk2 - Bad and missing. So as you can see. Parity shows good. Disk1 (MPN) which is the original disk, has been forgotten for some reason. Disk2 (2MZ) is bad and I plan to replace with a good 10Tb drive. What I need to do is get unRAID to "remember" Disk1 and rebuild to a new disk for disk2. How do i do this? I do not have any config backups. Any backups I had were on the array (lesson learned there). What can i do? Help me Tom Cruise, please and thank you! Edited September 8, 2022 by RussellG Quote Link to comment
trurl Posted September 8, 2022 Share Posted September 8, 2022 Do you have a new 10TB disk ready to assign as disk2? Quote Link to comment
trurl Posted September 8, 2022 Share Posted September 8, 2022 Don't do anything without further advice Quote Link to comment
RussellG Posted September 8, 2022 Author Share Posted September 8, 2022 19 minutes ago, trurl said: Do you have a new 10TB disk ready to assign as disk2? I do. 19 minutes ago, trurl said: Don't do anything without further advice 10-4 Quote Link to comment
trurl Posted September 8, 2022 Share Posted September 8, 2022 Attach diagnostics to your NEXT post in this thread. Quote Link to comment
trurl Posted September 8, 2022 Share Posted September 8, 2022 Will check back tomorrow 2 hours ago, trurl said: Don't do anything without further advice Quote Link to comment
JorgeB Posted September 8, 2022 Share Posted September 8, 2022 Like mentioned post the diags but you should be able to do a new config to make Unraid accept the new disk to rebuild the missing one, as long as parity is valid. Quote Link to comment
RussellG Posted September 8, 2022 Author Share Posted September 8, 2022 10 hours ago, trurl said: Attach diagnostics to your NEXT post in this thread. unraid-diagnostics-20220908-0855.zip Attached, apologies I dropped out yesterday. It was late over here. Quote Link to comment
trurl Posted September 8, 2022 Share Posted September 8, 2022 Follow these instruction carefully. We will check along the way to make sure things are as they should be. If things don't seem to be working as described, or you have questions, ask. Install new disk2 Go to Tools - New Config, Retain All, Apply Assign new disk2 Check BOTH Maintenance mode AND Parity Valid boxes Start the array Then post a screenshot Quote Link to comment
RussellG Posted September 8, 2022 Author Share Posted September 8, 2022 2 minutes ago, trurl said: Follow these instruction carefully. We will check along the way to make sure things are as they should be. If things don't seem to be working as described, or you have questions, ask. Install new disk2 Go to Tools - New Config, Retain All, Apply Assign new disk2 Check BOTH Maintenance mode AND Parity Valid boxes Start the array Then post a screenshot Ok, i am out for about 3-4 hours and will begin that when i get back. In the event Disk1 is bad, this would not do anything to the parity disk, correct? I ask because the old Disk2 may be repairable I am still looking at purchasing another WD100EZAZ drive and taking that PCB, swapping ROM IC and fixing it. i guess i could just mount disk1 and look at its contents to somewhat verify it’s ok? Quote Link to comment
trurl Posted September 8, 2022 Share Posted September 8, 2022 2 minutes ago, RussellG said: In the event Disk1 is bad Disk1 SMART looked OK except for 1 Reallocated which should be fine. If you want, you can run an extended self-test on disk1 before starting the above instructions. It would take many hours to complete. 5 minutes ago, RussellG said: this would not do anything to the parity disk, correct? Since New Config will be with Parity Valid, and array is started in Maintenance mode, no disks will be modified. 5 minutes ago, RussellG said: mount disk1 and look at its contents In later steps, you will be able to take a look at the contents of both disk1 and emulated disk2 before trying to rebuild anything. 12 minutes ago, RussellG said: old Disk2 may be repairable I am still looking at purchasing another WD100EZAZ drive and taking that PCB, swapping ROM IC and fixing it. That might be useful depending on how things go with trying to rebuild to a new disk. Quote Link to comment
trurl Posted September 8, 2022 Share Posted September 8, 2022 46 minutes ago, RussellG said: mount disk1 and look at its contents This is more complicated than it sounds and no need to try. 30 minutes ago, trurl said: In later steps, you will be able to take a look at the contents of both disk1 and emulated disk2 before trying to rebuild anything. Quote Link to comment
RussellG Posted September 8, 2022 Author Share Posted September 8, 2022 4 hours ago, trurl said: Follow these instruction carefully. We will check along the way to make sure things are as they should be. If things don't seem to be working as described, or you have questions, ask. Install new disk2 Go to Tools - New Config, Retain All, Apply Assign new disk2 Check BOTH Maintenance mode AND Parity Valid boxes Start the array Then post a screenshot Alright, Done with all those steps. Screenshot: Quote Link to comment
trurl Posted September 8, 2022 Share Posted September 8, 2022 OK Stop the array, set disk2 to Not Assigned Start the array in Normal mode (don't check Maintenance mode) Post a screenshot and new diagnostics Quote Link to comment
RussellG Posted September 8, 2022 Author Share Posted September 8, 2022 (edited) 2 hours ago, trurl said: OK Stop the array, set disk2 to Not Assigned Start the array in Normal mode (don't check Maintenance mode) Post a screenshot and new diagnostics Ok, to confirm, do not check maintenance mode. It also wants me check this to start it: Edited September 8, 2022 by RussellG Quote Link to comment
trurl Posted September 8, 2022 Share Posted September 8, 2022 yes you want to do this. Really the whole point, since the missing disk has no data yet, we want to see what the emulated disk looks like Quote Link to comment
trurl Posted September 9, 2022 Share Posted September 9, 2022 If emulated disk2 shows as unmountable, DO NOT FORMAT. I will check back tomorrow Quote Link to comment
RussellG Posted September 9, 2022 Author Share Posted September 9, 2022 (edited) 32 minutes ago, trurl said: If emulated disk2 shows as unmountable, DO NOT FORMAT. I will check back tomorrow Ok, so it started. And everything looks ok at first glance and a few spot checks? Requested diags and SS attached. 32 minutes ago, trurl said: If emulated disk2 shows as unmountable, DO NOT FORMAT. I will check back tomorrow Roger. I am going to stop it for the night. unraid-diagnostics-20220908-2238.zip Edited September 9, 2022 by RussellG Quote Link to comment
trurl Posted September 9, 2022 Share Posted September 9, 2022 That shows emulated disk2 is mounted and 70% full. So all you have to do is rebuild! 16 hours ago, trurl said: In later steps, you will be able to take a look at the contents of both disk1 and emulated disk2 before trying to rebuild anything. You are at that step now. Quote Link to comment
RussellG Posted September 9, 2022 Author Share Posted September 9, 2022 3 hours ago, trurl said: That shows emulated disk2 is mounted and 70% full. So all you have to do is rebuild! You are at that step now. Fingers crossed. Started rebuild with new disk. Thank you for your help! Sent over some beer/pizza funds as thanks. Quote Link to comment
trurl Posted September 9, 2022 Share Posted September 9, 2022 Thanks for the donation! Let us know how it goes. Quote Link to comment
RussellG Posted September 9, 2022 Author Share Posted September 9, 2022 1 hour ago, trurl said: Thanks for the donation! Let us know how it goes. Going Slowly 🥲 Quote Link to comment
trurl Posted September 9, 2022 Share Posted September 9, 2022 Post new diagnostics Quote Link to comment
RussellG Posted September 9, 2022 Author Share Posted September 9, 2022 (edited) 33 minutes ago, trurl said: Post new diagnostics Got it to speed up a good bit by disabling docker. Probably some of my containers trying to do things. Diags attached unraid-diagnostics-20220909-1012.zip Edited September 9, 2022 by RussellG Quote Link to comment
JorgeB Posted September 9, 2022 Share Posted September 9, 2022 Problem is disk2, it's failing: === START OF READ SMART DATA SECTION === SMART Health Status: FAILURE PREDICTION THRESHOLD EXCEEDED: ascq=0xfd [asc=5d, ascq=fd] Do you have another spare? Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.