oblivion2k Posted July 23, 2023 Share Posted July 23, 2023 Bought two exos 18tb drives to replace a single, smaller parity drive. Planned to start the array and let it rebuild, then install the old parity drive as a data drive. However, the new disks do not show up as unassigned devices or with lsscsi Troubleshooting steps so far: Created a new config: Disks predictably lost their assignments, but new disks are not visible. Rebooted server: No change. Installed a drive that was previously part of the array to rule out sudden hardware failure on the sata port where one of the new drives will be installed: drive showed up as predicted. Disk swapped back to the new drive, new drive did not show up. Attached both drives to other computers to rule out double-DOA: Both disks show up on both windows and linux mint PCs. Diagnostics attached. serbur-diagnostics-20230723-1501.zip Quote Link to comment
cYnIx Posted July 24, 2023 Share Posted July 24, 2023 Are you trying to add SAS hard drives to a SATA system? You may need a different HD controller to run these drives if so. Quote Link to comment
dlandon Posted July 24, 2023 Share Posted July 24, 2023 Do the new drives show in the BIOS? Sounds like you might have a BIOS setup issue. Quote Link to comment
Solution itimpi Posted July 24, 2023 Solution Share Posted July 24, 2023 The other possibility is that the drives suffer from the 3.3v issue and need that pin taping off. Quote Link to comment
oblivion2k Posted July 24, 2023 Author Share Posted July 24, 2023 (edited) 1 hour ago, cYnIx said: Are you trying to add SAS hard drives to a SATA system? You may need a different HD controller to run these drives if so. All drives are SATA. Some drives are attached to an LSA card in IT mode. Those drives show up. If I unplug them and plug in the new drives, they don't show up. 1 hour ago, dlandon said: Do the new drives show in the BIOS? Sounds like you might have a BIOS setup issue. I haven't had the time or resources to check bios on a normally headless system. I'll see what I can find. If they don't show up in BIOS, what should I do about that? I can't think of any reason why a drive of a certain size would show up, but not a slightly larger drive, at least not on a modern system. 14 minutes ago, itimpi said: The other possibility is that the drives suffer from the 3.3v issue and need that pin taping off. My understanding is that that's specifically an issue to WD easystore shucked drives, but correct me if I'm wrong, please. Also, the drives show up normally on other systems, Windows and Linux. Edited July 24, 2023 by oblivion2k Quote Link to comment
itimpi Posted July 24, 2023 Share Posted July 24, 2023 It might be worth trying to boot your Unraid server of a Linux live distribution to see if the drives show up there? If they do not that would be a very good indication that the issue is at the hardware level. Quote Link to comment
Veah Posted July 24, 2023 Share Posted July 24, 2023 (edited) Do you know for certain that the new hdd is powering up? Can you hear/feel it spin up? Problem following from lsa to mb connector makes me think power delivery. Edit: double check all the cables Edited July 24, 2023 by Veah Quote Link to comment
oblivion2k Posted July 24, 2023 Author Share Posted July 24, 2023 (edited) I'm starting to think it's a 3.3v issue after all based on what I'm reading online. It's really the only thing that makes sense. I'll tape the pins and report back. Edited July 24, 2023 by oblivion2k Quote Link to comment
oblivion2k Posted July 25, 2023 Author Share Posted July 25, 2023 Confirmed 3.3v issue, thanks itimpi Quote Link to comment
itimpi Posted July 25, 2023 Share Posted July 25, 2023 13 hours ago, oblivion2k said: Confirmed 3.3v issue, thanks itimpi Glad to hear it was the issue. Originally this only seemed to happen on shucked WD drives, but it seems that other manufacturers/models can experience this issue. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.