Terrace Posted August 2, 2023 Share Posted August 2, 2023 After creating a lot of videos with Premiere Pro and using OBS with NDI on my VM It seems like my 8700k was the slowdown for premiere and loss of frames during streaming/recording on OBS. I'd decided today to do the research into overclocking, got the values entered, they looked good on the bios stating 4.8ghz instead of the 3.7ghz stock and was quite surprised when i turned everything on and it was set to stock, i noticed a unraid message saying: Aug 2 21:23:21 Tower kernel: tsc: Detected 3700.000 MHz processor Aug 2 21:23:21 Tower kernel: tsc: Detected 3699.850 MHz TSC went back into the bios, 4.8ghz, went back into unraid/VM 3.7ghz, then I did a lot of reading of people recommending not overclocking whilst using unraid, not even XMP (without knowing i'd had this on for 33 days so far) If I did want to try out overclocking before shelling out for a new MB/Processor, is there a safety I need to disable before unraid will allow me to overclock, or did perhaps something else go wrong that caused me to be at stock Ghz? Besides the money for a new MB/Processor I just brought the maximum amount of DDR4 ram THIS system could take it would be a shame to move onto another platform. Quote Link to comment
JorgeB Posted August 3, 2023 Share Posted August 3, 2023 We don't recommend overclocking a server, but you can do it if you want. Quote Link to comment
Frank1940 Posted August 3, 2023 Share Posted August 3, 2023 I have never heard of anything in Unraid which would indicate that it 'plays' with BIOS settings. I suspect some other problem. Has the MB battery reached its end-of-life? Did you remember to actually save those BIOS changes? (I don't play with BIOS often but I seem to recall that some of them do display multiple screens where you have to confirm updates.) Overclocking decreases stability of any server. Most of us want to avoid instability at any cost. If you do your research and don't push the individual hardware items that you actually have in your server beyond their capability, you might be able to get some improvement in performance. But you are not going to get much help here in getting things working properly. Quote Link to comment
Terrace Posted August 3, 2023 Author Share Posted August 3, 2023 Oh sure I get that i'm on my own if i try it, I just wonderered if Unraid turns anything back off after it starts to load. I really did change the settings and double checked and made sure they were loaded, I can even enter the bios and see they are all set, but once i get into unraid everything seems to be back at stock. I've actually ended up breaking my entire network today with the introduction of my network cards, i can't even access unraid properly from the other PC anymore and managed to wreck everything. Trying to get some live help via the unraid discord networking section because I think i'll need to be walked through a lot in real time, but i don't think anyone is about at the moment. Quote Link to comment
JorgeB Posted August 3, 2023 Share Posted August 3, 2023 1 hour ago, Terrace said: if Unraid turns anything back off after it starts to load. It doesn't, note that the MHZs Linux shows may not always be the correct ones. Quote Link to comment
Terrace Posted August 4, 2023 Author Share Posted August 4, 2023 (edited) So it's possible that as the bios was still showing 4.8ghz through multiple restarts that it really was running at 4.8 on the VM's and such? I wonder what the best way to test real cpu speed is. I'll take a look around on the internet. Seems like CPU-Z might show real speed rather than just reading out loud what's displayed in the windows panel. I'll try to find the time to turn the overclock settings back on and run CPU-Z. Thanks for pointing me in the right direction with unraid not turning off anything. I hope CPU-Z can still read a Virtual Machine setup Edited August 4, 2023 by Terrace Quote Link to comment
Solution ConnerVT Posted August 4, 2023 Solution Share Posted August 4, 2023 Try this: watch -n1 "grep \"^[c]pu MHz\" /proc/cpuinfo" Quote Link to comment
JorgeB Posted August 5, 2023 Share Posted August 5, 2023 10 hours ago, Terrace said: I hope CPU-Z can still read a Virtual Machine setup I don't think it can. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.