Prowler Posted November 30, 2023 Share Posted November 30, 2023 Hi, Upgrading my 10TB to 22TB parity Done the usually pre clear successfully! assigned the 22TB to parity 2 this morning before I left for work and upon my return its only at 0.2% in with an estimated 328 days till completion at 728KB/s. is this normal? surely it shouldn't take a year! Any help would be grateful! Quote Link to comment
JorgeB Posted November 30, 2023 Share Posted November 30, 2023 Please post the diagnostics. Quote Link to comment
Prowler Posted November 30, 2023 Author Share Posted November 30, 2023 Do you want the whole zip? Quote Link to comment
itimpi Posted November 30, 2023 Share Posted November 30, 2023 6 minutes ago, Prowler said: Do you want the whole zip? Yes. Do you have anything accessing the array? This will severely affect the parity sinc speed whole it is happening. Quote Link to comment
Prowler Posted November 30, 2023 Author Share Posted November 30, 2023 Its solely a Plex server prowler-diagnostics-20231130-1633.zip Quote Link to comment
itimpi Posted November 30, 2023 Share Posted November 30, 2023 You are getting continual resets on parity2. You should carefully check the power and SATA cabling to the drive. Quote Link to comment
Prowler Posted November 30, 2023 Author Share Posted November 30, 2023 Ok, Anything i should be looking for? Quote Link to comment
Prowler Posted November 30, 2023 Author Share Posted November 30, 2023 So ive checked the sata cable, seems firmly in place! But can hear a sound like the needle is bouncing then an audible tone like its trying re engage every 5 secs Quote Link to comment
Solution itimpi Posted November 30, 2023 Solution Share Posted November 30, 2023 6 minutes ago, Prowler said: So ive checked the sata cable, seems firmly in place! But can hear a sound like the needle is bouncing then an audible tone like its trying re engage every 5 secs What about the power to the drive? The noises could be an indication of insufficient power. Do you use power splitters to get enough connections - they can cause problems. You could try swapping the power cables with another drive to see if the problem stays with the drive or moves with the cable change. Quote Link to comment
Prowler Posted November 30, 2023 Author Share Posted November 30, 2023 (edited) the disks are in a tower unit with a hot swap front, so only 1 cable providing the power to the unit, then individual sata cables coming from the back plate to the mother board Edited November 30, 2023 by Prowler Quote Link to comment
itimpi Posted November 30, 2023 Share Posted November 30, 2023 2 minutes ago, Prowler said: the disks are in a tower unit with a hot swap front, so only 1 cable providing the power to the unit, then individual sata cables coming from the back plate to the mother board Can you swap the disk to another position? Unraid does not care where drives are connected as it identifies them by serial number. Quote Link to comment
Prowler Posted November 30, 2023 Author Share Posted November 30, 2023 ok, will look into this! so i need to cancel the parity sync that im currently doing? Quote Link to comment
itimpi Posted November 30, 2023 Share Posted November 30, 2023 Just now, Prowler said: ok, will look into this! so i need to cancel the parity sync that im currently doing? Yes - it is going to take forever. I normally expect it to take ~2 hours per TB as a rule of thumb so MUCH quicker than you are currently getting. Before doing anything you might want to have a quick look at the syslog (via button at top right of GUI to see the continual reset on ata2 (which is the parity2 drive) as that shows you the symptom in the log when you have such an issue. Quote Link to comment
Prowler Posted November 30, 2023 Author Share Posted November 30, 2023 ok thanks, i wont have to do another pre clear surely? Quote Link to comment
itimpi Posted November 30, 2023 Share Posted November 30, 2023 3 minutes ago, Prowler said: ok thanks, i wont have to do another pre clear surely? No. A parity sync overwrites everything on a drive so existing contents are irrelevant. As a point to note a preclear is never NEEDED. It is just often done as a confidence check on a drive. You might find this section of the online documentation that discusses this to be of interest. Quote Link to comment
Prowler Posted November 30, 2023 Author Share Posted November 30, 2023 Thankyou for all your help, much appreciated Quote Link to comment
Prowler Posted November 30, 2023 Author Share Posted November 30, 2023 2 hours ago, itimpi said: What about the power to the drive? The noises could be an indication of insufficient power. Do you use power splitters to get enough connections - they can cause problems. You could try swapping the power cables with another drive to see if the problem stays with the drive or moves with the cable change. Thankyou for all the help! Was definitely a power issue. Moved the drive to a independent power supply and were moving along quite rapidly now. Quote Link to comment
JonathanM Posted December 5, 2023 Share Posted December 5, 2023 On 11/30/2023 at 12:12 PM, Prowler said: the disks are in a tower unit with a hot swap front, so only 1 cable providing the power to the unit Many (most?) hot swap bays have multiple power input connections, typically each power input should be fed from a dedicated lead from the PSU. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.