Jump to content
225redstick

SOLVED - HELP new router, no ip, not connecting

10 posts in this topic Last Reply

Recommended Posts

#ifconfig eth0

unraid eth0: flags=4416<UP,BROADCAST,RUNNING,SLAVE,MULTICAST> mtu 1500

 

 

Edited by 225redstick
edit

Share this post


Link to post

dosent show ip here like it use to: 

eth0: flags=6211<UP,BROADCAST,RUNNING,SLAVE,MULTICAST>  mtu 1500
        ether XXXXXXXXXXXX  txqueuelen 1000  (Ethernet)
        RX packets 2318  bytes 1020947 (997.0 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 1831  bytes 1402158 (1.3 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 20  memory 0xdfb00000-dfb20000

Edited by 225redstick
edit

Share this post


Link to post
21 minutes ago, 225redstick said:

dosent show ip here like it use to: 

eth0: flags=6211<UP,BROADCAST,RUNNING,SLAVE,MULTICAST>  mtu 1500
        ether 00:25:90:a3:ff:87  txqueuelen 1000  (Ethernet)
        RX packets 2318  bytes 1020947 (997.0 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 1831  bytes 1402158 (1.3 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 20  memory 0xdfb00000-dfb20000

Your router leased 192.168.1.5 to br0 not to eth0.

 

Do you have bridging enabled for eth0 in Settings --> Network?

 

image.png.4e6a28d63894ff4500b0872f9307062c.png

 

What does ifconfig show for br0?

 

 

Edited by Hoopster
  • Like 1

Share this post


Link to post

"Your router leased 192.168.1.5 to br0 not to eth0" i do remember trying to reserve that ip in router settings for DHCP unraid initial assignment? no reservation in router settings is showing up since I reset the router.

 

"Do you have bridging enabled for eth0 in Settings --> Network"? yes it was turned on, i dont remember doing that but maybe for an earlier docker install. i just tried turning it off.

Share this post


Link to post

the other thing i tried earlier in an attempt to return to the default DHCP configuration was to pull the usb unraid boot drive and to delete the boot/config/network.cfg and boot/config/network-riles.cfg files. 

Share this post


Link to post

bond0: flags=5443<UP,BROADCAST,RUNNING,PROMISC,MASTER,MULTICAST>  mtu 1500
        inet6 XXXXXXXXXXXXX  prefixlen 64  scopeid 0x20<link>
        ether XXXXXXXXXXXXX  txqueuelen 1000  (Ethernet)
        RX packets 954  bytes 130622 (127.5 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 749  bytes 802552 (783.7 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

br0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.7  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 XXXXXXXXXXXXX  prefixlen 64  scopeid 0x20<link>
        ether XXXXXXXXXXXXX  txqueuelen 1000  (Ethernet)
        RX packets 773  bytes 83939 (81.9 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 308  bytes 771747 (753.6 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

eth0: flags=6211<UP,BROADCAST,RUNNING,SLAVE,MULTICAST>  mtu 1500
        ether XXXXXXXXXXXXX  txqueuelen 1000  (Ethernet)
        RX packets 954  bytes 130622 (127.5 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 749  bytes 802552 (783.7 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 20  memory 0xdfb00000-dfb20000

eth1: flags=6147<UP,BROADCAST,SLAVE,MULTICAST>  mtu 1500
        ether XXXXXXXXXXXXX  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 16  memory 0xdf900000-df920000

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 2  bytes 140 (140.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 2  bytes 140 (140.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

Edited by 225redstick
edit

Share this post


Link to post

I think i figured it out for now, somehow bonding and bridging were on "yes" and seemed to be preventing the new router from connecting and configuring eth0. Thanks for suggestions and help and a little bit of trial and error :) I was worried my jump drive and/or network card were shot. 

 

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.7  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 XXXXXXXXXXXXXX  prefixlen 64  scopeid 0x20<link>
        ether XXXXXXXXXXXXXX  txqueuelen 1000  (Ethernet)
        RX packets 1645  bytes 267297 (261.0 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 957  bytes 750155 (732.5 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 20  memory 0xdfb00000-dfb20000

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now