Vr2Io

Usually doesn't matter, but best use USB 2.0 port.

Pls confirm
USB boot is enable, and assign it is 1st boot device
EFI folder no "-"

Look like problem relate ISP's IP change, due to not sure how you remote access your network and overcome this, but most likely reboot won't solve the problem.

BTW, push power button usually perform normal shutdown, but don't hold the button too long, otherwise it will power-off immediately instead soft shutdown, we don't want corrupt file system.

- Yes
- No
 
I would say Unraid not Support / work well for what you want.

Both Yes.

Then suggest temporary disable aggregation to verify.

Problem should relate fast boot have turn on. Pls ensure it is off in Bios setting.

Disk 已 drop, 你可以從新加入硬碟 rebuild. 不過如之前所說, 檢驗時硬碟不會 spindown, 所以問題不在 spindown.

You should try disable bonding, those usually trouble and your problem also self fix in few min.

You have passthrough all NIC
 
01:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller I226-V [8086:125c] (rev 04)
    Subsystem: Intel Corporation Device [8086:0000]
    Kernel driver in use: vfio-pci
    Kernel modules: igc
02:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller I226-V [8086:125c] (rev 04)
    Subsystem: Intel Corporation Device [8086:0000]
    Kernel driver in use: vfio-pci
    Kernel modules: igc
03:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller I226-V [8086:125c] (rev 04)
    Subsystem: Intel Corporation Device [8086:0000]
    Kernel driver in use: vfio-pci
    Kernel modules: igc
04:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller I226-V [8086:125c] (rev 04)
    Subsystem: Intel Corporation Device [8086:0000]
    Kernel driver in use: vfio-pci
    Kernel modules: igc
05:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller I226-V [8086:125c] (rev 04)
    Subsystem: Intel Corporation Device [8086:0000]
    Kernel driver in use: vfio-pci
    Kernel modules: igc

Bus 001 是 USB 2, Bus 002 才是 USB 3.
 
Bus 002 Device 002: ID 0951:1666 Kingston Technology DataTraveler 100 G3/G4/SE9 G2/50
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 174c:55aa ASMedia Technology Inc. ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge, ASM1153E SATA 6Gb/s bridge
Bus 001 Device 009: ID 2109:8817 VIA Labs, Inc. USB Billboard Device   
Bus 001 Device 008: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS578 SATA 6Gb/s
Bus 001 Device 012: ID 2109:8817 VIA Labs, Inc. USB Billboard Device   
Bus 001 Device 011: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS578 SATA 6Gb/s
Bus 001 Device 010: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS578 SATA 6Gb/s
Bus 001 Device 007: ID 2109:2817 VIA Labs, Inc. USB2.0 Hub             
Bus 001 Device 006: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS578 SATA 6Gb/s
Bus 001 Device 005: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS578 SATA 6Gb/s
Bus 001 Device 003: ID 2109:2817 VIA Labs, Inc. USB2.0 Hub             
Bus 001 Device 002: ID 2109:2820 VIA Labs, Inc. VL820 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
 

That means system couldn't resume after sleep. Not all system can resume after sleep, you may try tuning some BIOS setting to fix that.

To be more solid, you could try one more parity check, if result positive could assume problem cause by plugin, then rule out which one is. I would suggest uninstall disklocation first.

In most case, problem come from battery, pls apply similar loading and further test the UPS to confirm.
 
Below are one example
 
 

First, I have assume the backup was a single image file, but according your descriptions it likely was a branch directory and file backup of the USB, does it correct ?
 
 If that, you need assign all disk to array to get whole directory and file from different disk. Don't assign any disk to parity.

There have two easy way.
 
1. temporary change the client PC IP ( static ) to original IP subnet to access Unraid again, no need setting DNS or gateway. Then access the web GUI and change the IP which you like.
2. Shutdown Unraid by press power buttom once, then insert the USB to PC and edit /config/network.cfg.

/boot/config/parity-checks.log

igc means 2.5G and ix1 is 10G ? But why ix1 was linkdown ?
 
Does mlx4 00:02:c9:56:8c:1e show in router ?
 
# PCI device 0x15b3:0x6750 (mlx4_core)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:02:c9:56:8c:1e", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
 
If you can access Unraid locally and make test on 10g have pass some network test, i.e. ping other client and router, then problem likely opensense relate.

Check does the LED on network card and router/switch have change, it show link / speed status.
 
If you have keyboard monitor attach to Unraid , then access it local and provide the diagnostics ( tools -> diagnostics ) file here.
 

 

你試下禁止"主機訪問自定義網絡", 看看有否不同. 另外亦試下刪除那個 emby 自定義網絡.
 
另外, 軟路由可以做到雙 WAN 吧, 那樣不用兩隻軟路由, LAN + vlan 行一個網口就可.

Unifi claim 2nd hardware version of 16XG have fix copper port 10G issue, check your switch HW version and get help in Unifi forum.

The enclosure have detect.
 
Feb 18 16:00:13 VMHost kernel: scsi 2:0:0:0: Enclosure         Promise  J830s            060= PQ: 0 ANSI: 6
Feb 18 16:00:13 VMHost kernel: scsi 2:0:0:0: set ignore_delay_remove for handle(0x000a)
Feb 18 16:00:13 VMHost kernel: scsi 2:0:0:0: SES: handle(0x000a), sas_addr(0x500015554091333e), phy(36), device_name(0x0000000000000000)
Feb 18 16:00:13 VMHost kernel: scsi 2:0:0:0: enclosure logical id (0x500015554091333f), slot(36) 
Feb 18 16:00:13 VMHost kernel: scsi 2:0:0:0: qdepth(254), tagged(1), scsi_level(7), cmd_que(1)
Feb 18 16:00:13 VMHost kernel: scsi 2:0:0:0: Attached scsi generic sg5 type 13
 
But end-up no response and remove.
 
Feb 18 16:18:47 VMHost kernel:     expander present: handle(0x0009), sas_addr(0x500015554091333f), port:255
Feb 18 16:18:47 VMHost kernel: mpt2sas_cm0: search for expanders: complete
Feb 18 16:18:47 VMHost kernel: mpt2sas_cm0: mpt3sas_base_hard_reset_handler: SUCCESS
Feb 18 16:18:47 VMHost kernel: mpt2sas_cm0: _base_fault_reset_work: hard reset: success
Feb 18 16:18:47 VMHost kernel: mpt2sas_cm0: removing unresponding devices: start
Feb 18 16:18:47 VMHost kernel: mpt2sas_cm0: removing unresponding devices: end-devices
Feb 18 16:18:47 VMHost kernel: mpt2sas_cm0: Removing unresponding devices: pcie end-devices
Feb 18 16:18:47 VMHost kernel: mpt2sas_cm0: removing unresponding devices: expanders
Feb 18 16:18:47 VMHost kernel: mpt2sas_cm0: removing unresponding devices: complete

Docker are use Unraid DNS setting, it won't use LAN DHCP even allocate IP.

Pls try use IP access SMB in Windows, i.e. \\10.0.0.1
 
Your eth1 10.0.0.1 setting subnet in /24, so Windows side need setting to 255.255.255.0 instead 255.0.0.0

From description, it show memory stick was good, just can't run in dual stick with current mobo, that's why I suggest you clock down the memory clock. Those problem are quite common and RMA those strick won't help much.

This normal.