mortsonian Posted August 10, 2019 Share Posted August 10, 2019 The last couple of days, I have been trying out Unraid, but it doesn't run for more than a couple of hours before it goes unresponsive and I have to hard reset it (long push). Sometimes I even have to delete the network config off the USB. Are there any logfiles that doesn't get wiped off the memory? Quote Link to comment
trurl Posted August 10, 2019 Share Posted August 10, 2019 2 hours ago, mortsonian said: Are there any logfiles that doesn't get wiped off the memory? The latest versions of Unraid have a syslog server feature that allow you to designate where to save syslog. While ideally any diagnostics would be taken before rebooting, a diagnostic taken after reboot might tell us something. Have you done a memtest? How is the CPU cooling? Quote Link to comment
mortsonian Posted August 11, 2019 Author Share Posted August 11, 2019 I turned on the syslog server and found out it had some hardware error. After a some Memtest86, i found the RAM blocks that were causing the issue. Quote Link to comment
trurl Posted August 11, 2019 Share Posted August 11, 2019 3 hours ago, mortsonian said: i found the RAM blocks that were causing the issue. 👍 Quote Link to comment
mortsonian Posted August 14, 2019 Author Share Posted August 14, 2019 Sadly as it is, it still is crashing and i can't figure out what to do. I attached the syslog syslog Quote Link to comment
trurl Posted August 14, 2019 Share Posted August 14, 2019 The syslog seems to indicate it couldn't contact limetech (required for trial key) and never started the array. That's the last thing I see. Are you saying it crashed after that? Will it work long enough for you to access the webUI and get us a Diagnostic? Tools - Diagnostics, attach complete zip file to your next post. Have you tried another memtest? Are you sure the CPU cooling is OK? Power supply? Quote Link to comment
mortsonian Posted August 14, 2019 Author Share Posted August 14, 2019 Yes, that was one of the times it crashed. After that i removed the network config from the USB and booted the server up again and now it's been running for 44 minutes. It normally runs for a couple of hours before it becomes unresponsive (still powered on, but no WebUI and i can't ping). The last Memtest i ran, was clean. 0 Errors. The CPU cooler is fine and the temp is at 29.8C. I don't know about the PSU, but think it's fine (Corsair RM450). tower-diagnostics-20190814-1810.zip Quote Link to comment
superloopy1 Posted August 14, 2019 Share Posted August 14, 2019 (edited) I lived with this problem for a few days after ugrading to 6.7.2. Eventually ended up back on 6.7, was going to go back as far as 6.6.7 but havent needed to, and server stable again, i was having to pull the plug, restart and resync parity for ever it seemed. Do you run unassigned devices or preclear plugin as removing both of those seems to have stabilised my system. Not saying these in any way contributed but removal has contributed to a stable system it seems. See my post Seems we're both members of an exclusive club eh ... Edited August 14, 2019 by superloopy1 Quote Link to comment
trurl Posted August 14, 2019 Share Posted August 14, 2019 8 minutes ago, superloopy1 said: Do you run unassigned devices or preclear plugin as removing both of those seems to have stabilised my system. My philosophy is to not have preclear installed unless I am going to use it right away, then remove it when finished. Never had any trouble with UD. And in general, don't install plugins you don't need and don't install packages from Nerdpack you don't need. Quote Link to comment
mortsonian Posted August 14, 2019 Author Share Posted August 14, 2019 28 minutes ago, superloopy1 said: Do you run unassigned devices or preclear plugin as removing both of those seems to have stabilised my system. I have both, because i'm not done setting up the server yet. It crashed several times, while i was preclearing the first disk. That is why i have postponed the second drive. I hoped to fix the crashing issue before i have to run preclear again. Quote Link to comment
mortsonian Posted August 17, 2019 Author Share Posted August 17, 2019 Alright. So now i precleared the disk (ofc the server crashed 10 times while i was doing it). I uninstalled preclear and tried to set the freshly precleared disk as a parity. But it still constantly crashes while building the parity and then has to start from the beginning. Fix common problems, has also bugged out about hardware errors and told me to install mcetools. I've done that, but i can't find the logs to determine what hardware is the cause. Here's the newest syslog. syslog Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.