Timothyy Posted June 6, 2020 Share Posted June 6, 2020 My unraid server v6.8.3 seems not to reboot properly. I can only get the unraid server functionally running after a full power off after having waited for a long moment or pulling the power cord. If I reboot the server or power it up after a shutdown too fast it does not start, screen stays black (have checked all video output cards to make sure I was not looking to the wrong screen). I checked my bios boot order also, and made sure the flash drive was on top (and yes it is saved). Not sure how to start troubleshooting now as my guess is that it does not call the flashdrive properly. When server is running I do not get any errors or so. I have 2 GPUs, slot 1 and 3 both equipped with a GTX 1080, and I have a factory vga connector connected via some sort of ide cable to the motherboard directly All three of them are working fine. Which is the primary one? The one on slot 1 or the one connected to the motherboard via cable? I notice that my motherboard output first is displaying on the vga (bios, load order, pre boot system check etc.) and then is switching. By the way if performing a reboot do I need to stop the array manually before. I currently am doing this for safety reasons anyway at a reboot or shut down but is it mandatory to stop the array first? Quote Link to comment
Frank1940 Posted June 7, 2020 Share Posted June 7, 2020 You should probably try the Syslog Server to capture what is going on. Instructions are in the his post: https://forums.unraid.net/topic/46802-faq-for-unraid-v6/page/2/?tab=comments#comment-781601 What happens if you try a full power down from the menu? I am assuming the you have one or more VM's. Have you tried stopping them? Quote Link to comment
Timothyy Posted June 7, 2020 Author Share Posted June 7, 2020 6 hours ago, Frank1940 said: What happens if you try a full power down from the menu? I am assuming the you have one or more VM's. Have you tried stopping them? I use the full power down from the menu and before switching off I made sure the VMs were off already. I also turned on the syslog mirror to flash now. Any direction on what to look for in the logs? Never really dived in to them. And what about the PCIe ACS override setting which is turned on? Could this cause some trouble with the reboot? Quote Link to comment
Frank1940 Posted June 7, 2020 Share Posted June 7, 2020 2 hours ago, Timothyy said: Any direction on what to look for in the logs? You will have to post up the file here. Be sure to note time when you did the test. Quote Link to comment
isrdude Posted June 17, 2020 Share Posted June 17, 2020 Same issue here. No VM, checked GPU, mobo, memory, connections, etc. all good. Must go to a complete power down then restart as reboot hangs after bizroot. Syslogs attached. Maybe this will help Timothyy too. tower-syslog-20200617-1407.zip Quote Link to comment
isrdude Posted August 21, 2020 Share Posted August 21, 2020 anyone??? Bueller? Bueller? Quote Link to comment
civic95man Posted August 21, 2020 Share Posted August 21, 2020 @isrdude Maybe try updating the BIOS, you seem to be a few versions behind. Also try disabling "fast boot" or "quick boot" from the BIOS and see if that helps at all, if its enabled. Quote Link to comment
isrdude Posted August 21, 2020 Share Posted August 21, 2020 Thnk you...I'll give it a try! Quote Link to comment
isrdude Posted August 21, 2020 Share Posted August 21, 2020 Thanks civic95man....it was the "fast boot"! Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.