Muhamad Aidil Karim

Just to update on this issue. Flash newer bios on the motherboard seems to fixed this issue. Running 2 weeks now without freeze.

Hi @JorgeB, thanks for the reply. During crash, I have several VM and Docker running as well. Intel vt already enable on my motherboard. FYI, the diagnostic log is capture after power cycle the unit. The syslog is captured before the event happen.

Hi, I am having issue because sometime my unraid is freeze and cannot be accessible. I can only start back the server after cycle power. Hope someone can suggest what i can do to avoid issue from happen again. Herewith i attach the diagnostic file and some log that being captured via remote syslog server. Unraid Version: 6.11.5 Motherboard: Gigabyte Technology Co., Ltd. Z490 VISION G Processor: Intel® Core™ i9-10850K CPU @ 3.60GHz RAM: 64 GB Thank you. aiesb-svr-01-diagnostics-20230313-1116.zip aiesb-svr-syslog.log

Hi JorgeB, Now i added back "Dev 3" in the cache pool and balancing is running. Hopefully my new nvme ssd no repeated issue again. Thanks you very much for your help 👍

Hi JorgeB, Thanks for quick reply. You are saving my day. Now the cache pool is up again. I attach new diags just in case. aiesb-svr-01-diagnostics-20221111-1851.zip Is it safe to add back "Dev 3" to the pool as redundancy?

Hi , Hopefully you guys can help me out for this issue. I add 1 more nvme ssd to cache pool as redundancy and the process is success. However after 1 day, the new nvme ssd got issue and not detected. I remove back the ssd from the cache pool because it detect no device & the system run as normal with single nvme ssd cache pool. Today 1 re-seat the nvme back and got detect by the system back (as unasigned device), but the original cache pool nvme ssd show "Unmountable: No pool uuid". I found this thread in the forum but not sure is this the same solution to run command below? btrfs-select-super -s 1 /dev/sdX1 I afraid if i run the command will loose all my data. Got my several important vm inside. 🤕 Need you guys help on this. I attach also the diagnostic file. aiesb-svr-01-diagnostics-20221111-1502.zip Thanks guys.

Thank you for sharing your experience. I'll looking forward to include multi GPU in my build.

Hi, I am planning to deploy 2 VM on my unraid. Each VM will have dedicated GPU assigned. Is there any requirement for this setup? Can I used same GPU model on my unraid? My current setup are as below: Motherboard: GIGABYTE Z490 VISION G Processor: CORE I9 10900K RAM: VENGEANCE LPX CMK (3600) 16GB x 2

Update: Today i have upgrade from 6.8.3 to 6.9.1, my onboard NIC are now detected correctly and can be used.

Dear itimpi, Thank you for the reply and support. I will try once next stable release is out. Currently my setup runs several VM which I migrate from previous platform (Hyper-V) which cannot afford downtime. I will update when tested in next stable release. BTW, when target next stable release will be out?

Hi, I am quite new to unraid. After reading review and watch other build, I am decided to build one. I have new unraid 6.8.3 build with spec below: Motherboard: GIGABYTE Z490 VISION G Processor: CORE I9 10900K RAM: VENGEANCE LPX CMK (3600) 16GB x 2 I was unable to use build-in Intel 2.5G NIC. In the system devices it show: However, when I plugged-in the NIC to my switch (Gigabit Port), the system unable to get IP address. Since I am quite new to this, I did not have any idea to troubleshoot. I hope to get some help and answer here. Temporary I have added Realtek PCI Express Gigabit Ethernet temporary until this issue is fixed. Thank you.