Emanuel87

hi guys, i tried installing this container and it cannot get even past the installer. i have not yet figure out how to map the data folder, but even without that. once I create a username and ad the database the container will stop responding. anyone tried installing this lately? is this actively being supported?

Hello everyone. i am trying to figure out what is not working in my setup. I have swag and ApacheGuacamole on my unraid, and I cannot get fail2ban to work. in the swag dashboard I can see failed login attemps and that I have 2 ips in jail, but that doesn't stop my mobile from continously trying to log in (although it's banned). any idea what to do or how to debug this further? thank you.

wireguard is blocked by company it. so that's why i've asked for openVPN, as this is what the company also uses.

hi guys, I have a ASUS -tuf gamming h470-pro motherboard and i can't mange to get the fan speed controller to show any ideas. I am really annoyed as my temps are quite high during parrity because the fans never spin up . i don't really want them running fully on either, as that would drive me creazy and wear the fans out.

for those more challanged among us, could you please may detail also the assumed part

anyone? is there no support for the Ombi container?

hi guys. I have problem with the ombi container with a subdomain. I have removed the base_URL variable and installed the container. i have corectly configured swag but i cannot reach ombi from outside my network. I have tripple checked the setting and everything is left on default. I am using the customer netwrok that swag is on. I am inclined to believe there is something I'm missing when configuring ombi, because nextcloud works flawlesly. can anyone provide any suggestions? thank you.

that might make some sense. I just got yesterday an error that the flash is read only. that might be the case that the flash was getting corrupted and I didn't realized that. funny enough today I am not getting that error anymore. but I will replace it tomorrow with a new one, just to eliminate this problem

so then why does unraid keep saying unclean shutdown?:(

did that. it takes aroung 50 seconds. so my 480 Shutdown time-out should be sufficient. yet I have a feeling unraid is ignoring this, as it was rebooted in less than 3 minutes

i don't know. where can I check that? I had the timeout at around 3 minutes. personally, i think it takes less than 1 minute, but I might be wrong. I have now changed the setting to 7 minutes.

Hello everyone, Noob here. i have a problem with my server. after almost every restart or shutdown i get a prarity check due to unclear shutdown. I have no idea why this keeps happening, but it's driving me crazy. can anyone help? I ahve attached the diagnostics file, if that could help. thank you. tower-diagnostics-20210913-2221.zip

thank you for the explanation. I also understood cache yes as you described, but I was under the impression that with mover tuning plugin I can set the mover to only run when the cache is 75% full. that way the thing would move to cache only when the cache gets full. is that right? I am seeding but from the logs show that it's actually pulling stuff directly to the cache as the files get modified or created

Hi guys, I have a problem. My disk1 would not spin down, and if I force it to spin down, it spins back up. I have installed the file activity tool and noticed that stuff is being written to the disk on my cache enabled "downloads" folder. Deluge is pulling the stuff. Does anyone have any idea why this happens? Mover is supposed to run every hour but I also have Mover Tuning plugin, that limits the transfer only when cache is above 75%. right now my cache is at 10%. but i am not sure if it's this, as the disk spin up always, not every hour. Anyone has any idea how to spin down the disks and keep them like that? I have attached also a diagnostic. Thank you. tower-diagnostics-20210715-2212.zip

thanks, it worked. unfortunately, I still can't figure out why my disk1 is spinning up with no activity

yes. like 5 times. including restarts and running the cleanup utility...

ok... i don;t know hwat to say. i have it installed.

thanks for the help. here you go. tower-diagnostics-20210713-1917.zip

hi. yes and yes

i've got exactly the same problem. the plugin does not start

thank you very much for the suggestion. in the end i started with a clean slate as besides replacing my cpu i also replaced the cache drives and it seems i really broke something. now i get the splash screen and i am slowly building my setup again thank you.

Hi guys, still new to unraid. i had ro replace my i3-10300 with an i5-11500 and since then I had a lot of headaches. Basically, all was running well on the old processor but since the new one, i keep haing problems with the video. I know the drivers are not in the latest kernel, so i added options i915 force_probe=4c8a to /boot/config/modprobe.d/i915.conf that seemed to work with plex hardware decoding. But I still ahve the problem at bootup where I cannot see the bootscreen to select between GUI and non-gui boot of unraid. strangely, the system cannot boot headless. I have to hit an enter after powerup otherwise it is stuck somewhere. I can't tell were as I cannot see anything on the screen. If i hit enter twice it seems to boot in the headless mode and then i cna see the command line. no matter how long i leave it there, it will not boot. it just hangs, and a short push on the power button will turn off the machine. Any advice for me? The MOBO is a H470 from asus with the lastest bios update,. I am really frustrated about this. Even a new install had the same problem (i wanted to start over as a cache disk replacement broke some of the containers). thank you.

@karateo I have just checked the card and it works. The seller seems to sell a lot of server hardware. The board looks used, even one of the fins of on the LSI chip cooler looks a bit banged, but the board runs. and at 45 Euros I'm happy with what I paid.

thank you Frank for the explanation. I stay with eBay as I have buyer's protection guarantee and in the worst case, if I have to ship the product back PayPal Germany pays for return shipping in this cases up to 25€ (or at least it did a few years ago)

i just bought one from Ebay from italy. the guy seems to have more, but give me a day to test mine out before buying: https://www.ebay.de/itm/Controller-SAS-D2607-A21-LSI9211-8i-Flash-in-IT-Mode-CAVO-SAS-4-porte-SATA/274744468973?hash=item3ff80be5ed:g:5yAAAOSwnEFf7a0P ebay germany allows you to filter for products which are within EU: https://www.ebay.de/sch/i.html?_from=R40&_nkw=lsi+9211-8i&_sacat=0&rt=nc&LH_PrefLoc=3