Emanuel87

Members
  • Posts

    24
  • Joined

  • Last visited

About Emanuel87

  • Birthday 02/18/1987

Converted

  • Location
    Germany
  • Personal Text
    ASUS TUF Gaming H470-PRO, 16Gb RAM, i5-11500

Emanuel87's Achievements

Newbie

Newbie (1/14)

4

Reputation

  1. that might make some sense. I just got yesterday an error that the flash is read only. that might be the case that the flash was getting corrupted and I didn't realized that. funny enough today I am not getting that error anymore. but I will replace it tomorrow with a new one, just to eliminate this problem
  2. so then why does unraid keep saying unclean shutdown?:(
  3. did that. it takes aroung 50 seconds. so my 480 Shutdown time-out should be sufficient. yet I have a feeling unraid is ignoring this, as it was rebooted in less than 3 minutes
  4. i don't know. where can I check that? I had the timeout at around 3 minutes. personally, i think it takes less than 1 minute, but I might be wrong. I have now changed the setting to 7 minutes.
  5. Hello everyone, Noob here. i have a problem with my server. after almost every restart or shutdown i get a prarity check due to unclear shutdown. I have no idea why this keeps happening, but it's driving me crazy. can anyone help? I ahve attached the diagnostics file, if that could help. thank you. tower-diagnostics-20210913-2221.zip
  6. thank you for the explanation. I also understood cache yes as you described, but I was under the impression that with mover tuning plugin I can set the mover to only run when the cache is 75% full. that way the thing would move to cache only when the cache gets full. is that right? I am seeding but from the logs show that it's actually pulling stuff directly to the cache as the files get modified or created
  7. Hi guys, I have a problem. My disk1 would not spin down, and if I force it to spin down, it spins back up. I have installed the file activity tool and noticed that stuff is being written to the disk on my cache enabled "downloads" folder. Deluge is pulling the stuff. Does anyone have any idea why this happens? Mover is supposed to run every hour but I also have Mover Tuning plugin, that limits the transfer only when cache is above 75%. right now my cache is at 10%. but i am not sure if it's this, as the disk spin up always, not every hour. Anyone has any idea how to spin down the disks and keep them like that? I have attached also a diagnostic. Thank you. tower-diagnostics-20210715-2212.zip
  8. thanks, it worked. unfortunately, I still can't figure out why my disk1 is spinning up with no activity
  9. yes. like 5 times. including restarts and running the cleanup utility...
  10. thanks for the help. here you go. tower-diagnostics-20210713-1917.zip
  11. thank you very much for the suggestion. in the end i started with a clean slate as besides replacing my cpu i also replaced the cache drives and it seems i really broke something. now i get the splash screen and i am slowly building my setup again thank you.
  12. Hi guys, still new to unraid. i had ro replace my i3-10300 with an i5-11500 and since then I had a lot of headaches. Basically, all was running well on the old processor but since the new one, i keep haing problems with the video. I know the drivers are not in the latest kernel, so i added options i915 force_probe=4c8a to /boot/config/modprobe.d/i915.conf that seemed to work with plex hardware decoding. But I still ahve the problem at bootup where I cannot see the bootscreen to select between GUI and non-gui boot of unraid. strangely, the system cannot boot headless. I have to hit an enter after powerup otherwise it is stuck somewhere. I can't tell were as I cannot see anything on the screen. If i hit enter twice it seems to boot in the headless mode and then i cna see the command line. no matter how long i leave it there, it will not boot. it just hangs, and a short push on the power button will turn off the machine. Any advice for me? The MOBO is a H470 from asus with the lastest bios update,. I am really frustrated about this. Even a new install had the same problem (i wanted to start over as a cache disk replacement broke some of the containers). thank you.