hermy65
-
Posts
273 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by hermy65
-
-
-
@GilbN here is what mine shows
-
3 minutes ago, GilbN said:
In the terminal what does
apcaccess | grep 'NOMPOWER\|LOAD'
output
@GilbN I get nothing when i run that
-
@falconexe i have my server ip configured in the apcupsd section of the telgraf config as shown
# # Monitor APC UPSes connected to apcupsd [[inputs.apcupsd]] # # A list of running apcupsd server to connect to. # # If not provided will default to tcp://127.0.0.1:3551 servers = ["tcp://192.168.0.50:3551"] # # ## Timeout for dialing server. # timeout = "5s"Maybe @GilbN has a little insight since he mentioned he is using the built in apc ups daemon as well.
-
@GilbN @falconexe - OK i moved my telegraf to host and its pulling in *some* UPS data but not all of it, also noticing some strange things with the array growth and the TX/RX numbers on my eth0 interface.
in #1 - my UPS stats are not all populating. Im using the APC UPS Daemon thats built into unraid if that matters.
in #2 - my annual array growth is less than my weekly/monthly
in #3 -randomly i will get massive numbers on this panel, i assume its just something weird on my end but thought i would bring it to your attention.
Also, random question, is there a way to convert the CPU temps to Farenheit?
-
4 minutes ago, GilbN said:
You can. I use it. As long as telegraf runs as host that should work. Is the deamon running on the host?
Ah, that may be my issue. My telegraf does not run as host so maybe thats why its not working?
-
@falconexe finally getting this setup and the main issue im running into so far is getting my UPS data to pull in. This is what my telegraf config looks like
# # Monitor APC UPSes connected to apcupsd [[inputs.apcupsd]] # # A list of running apcupsd server to connect to. # # If not provided will default to tcp://127.0.0.1:3551 # servers = ["tcp://127.0.0.1:3551"] # # ## Timeout for dialing server. # timeout = "5s"Im guessing i need to fill out the ip of my unraid server here since im using the built in APC UPS daemon under Settings -> UPS but when i try that it says no route to hose. Im guessing i need to configure something but im not sure what. Perhaps i cannot use the built in APC UPS daemon in unraid?
-
@falconexe yeah man im still here, just trying to take in what you have done here so far. Probably going to start playing with what you have here tomorrow and see what we can accomplish here. Great work again!
-
@falconexe Looking good! are you planning on releasing your dashboards once you are satisfied with them?
-
@falconexe Nice find - let us know if it works for you!
-
@falconexe / @KoNeko Perhaps we can push this idea towards one of the plugin devs here and they can make something like it or integrate it into an existing plugin they offer?
-
Not necessarily a support question but not sure where else to put this.
Is there a plugin/app of some sort that we can install in unRAID that will allow us to visualize our storage usage over time? Perhaps it would show how much additional storage we are using per month, etc? Per month storage burn might be helpful in determining when you need to get additional drives ,etc. Also, it could show you if there was a deletion of data or something of that sort as your usage would drop, etc?
-
1
-
-
53 minutes ago, johnnie.black said:
It will mount if all pool members are connected to the server (unless thee are other issues), and you just need to mount one of them, the others will be mounted together if found.
If you don't have the missing member it might mount in degraded mode if the pool was redundant, see here for command.
@johnnie.black I was able to find a potential 2nd drive that was part of it but was unable to get either to work using some of the commands from your link. Any other thoughts by chance?
root@RackServ:~# mount -o degraded,usebackuproot,ro /dev/sdn1 /x mount: /x: wrong fs type, bad option, bad superblock on /dev/sdn1, missing codepage or helper program, or other error. root@RackServ:~# mount -o ro,notreelog,nologreplay,degraded /dev/sdn1 /x mount: /x: wrong fs type, bad option, bad superblock on /dev/sdn1, missing codepage or helper program, or other error. root@RackServ:~# mount -o degraded,usebackuproot,ro /dev/sdo1 /x mount: /x: wrong fs type, bad option, bad superblock on /dev/sdo1, missing codepage or helper program, or other error. root@RackServ:~# mount -o ro,notreelog,nologreplay,degraded /dev/sdo1 /x mount: /x: wrong fs type, bad option, bad superblock on /dev/sdo1, missing codepage or helper program, or other error. root@RackServ:/mnt/disk4# btrfs restore -v /dev/sdn1 /mnt/disk4/mike warning, device 5 is missing warning, device 1 is missing bad tree block 2115388817408, bytenr mismatch, want=2115388817408, have=0 ERROR: cannot read chunk root Could not open root, trying backup super warning, device 5 is missing warning, device 1 is missing bad tree block 2115388817408, bytenr mismatch, want=2115388817408, have=0 ERROR: cannot read chunk root Could not open root, trying backup super warning, device 5 is missing warning, device 1 is missing bad tree block 2115388817408, bytenr mismatch, want=2115388817408, have=0 ERROR: cannot read chunk root Could not open root, trying backup super root@RackServ:/mnt/disk4# btrfs restore -v /dev/sdo1 /mnt/disk4/mike warning, device 1 is missing bad tree block 1754592444416, bytenr mismatch, want=1754592444416, have=0 Couldn't read tree root Could not open root, trying backup super warning, device 1 is missing bad tree block 1754592444416, bytenr mismatch, want=1754592444416, have=0 Couldn't read tree root Could not open root, trying backup super warning, device 1 is missing bad tree block 1754592444416, bytenr mismatch, want=1754592444416, have=0 Couldn't read tree root Could not open root, trying backup super -
I lost a few files that were on my cache drive and was hoping to recover them from some older drives that used to be my cache drives but when i try to mount them in Unassigned Devices i get the following. Is there any possible way for me to recover the files i need or am i out of luck?
May 21 09:03:38 RackServ kernel: BTRFS info (device sdn1): disk space caching is enabled May 21 09:03:38 RackServ kernel: BTRFS info (device sdn1): has skinny extents May 21 09:03:38 RackServ kernel: BTRFS error (device sdn1): devid 5 uuid 9203c653-08ef-4d3a-8068-fb91544bafcb is missing May 21 09:03:38 RackServ kernel: BTRFS error (device sdn1): failed to read the system array: -2 May 21 09:03:38 RackServ kernel: BTRFS error (device sdn1): open_ctree failed May 21 09:03:38 RackServ unassigned.devices: Mount of '/dev/sdn1' failed. Error message: mount: /mnt/disks/Samsung_SSD_850_EVO_500G: wrong fs type, bad option, bad superblock on /dev/sdn1, missing codepage or helper program, or other error. May 21 09:03:38 RackServ unassigned.devices: Partition 'Samsung SSD_850_EVO_500G' could not be mounted. -
@johnnie.black I guess im not following. Are you saying what i did earlier caused the issue?
-
@johnnie.black I followed your steps but when i re-add the drives and start the array i get an error that says: Cache drive unmountable, no pool uuid.
I tried the btrfs restore steps listed here and was able to recover data from the two drives in my original screenshot that were in unassigned devices but when i try it on the two disks that were listed in the pool in my original picture i get the error in the attached image.
-
@John_M It was RAID 1. I checked the cables and they all seem solid. I added the two drives back into the pool and started the array but now im getting this.
-
5 minutes ago, John_M said:
That is probably the clue. The SATA and/or power cables probably got disturbed. Samsung SSDs are incredibly fussy about their SATA cables at the best of time.
@John_M so do I just add them back into the cache pool then? Will I lose any data?
-
I moved my server to a new location, fired it up and for some reason 2 of my cache drives are now showing up in unassigned devices. If i add them i assume it rebuilds them but do i lose any data? Whats the best way to handle this so i dont lose anything on my cache drive? Also, why would this happen?
-
Having issues with mylar as of recently so i posted an issue on their github and this is what the dev said:
Cannot find /usr/lib/python2.7/site-packages/requests/__init__.py:91: RequestsDependencyWarning: urllib3 (1.25) or chardet (3.0.4) doesn't match a supported version!Quoteis repeated several times throughout thay logfile.
You need to update either/both of your python urllib3 and charset modules as they're not of the required build to use the library that mylar uses.
-
Ive got an issue that i cant resolve, hopefully you guys can tell me what dumb thing i did/did not do.
I have a handful of kodi boxes up and running pointing at a SQL database. I decided to setup this headless container to handle library updates but im running into an issue. All i did was setup the advancedsettings to point at the database then point sonarr at it but it doesnt update the library. In the kodi log file it says:
17:58:37.621 T:22745948530432 WARNING: Process directory 'smb://ip/folder/name of show' does not exist - skipping scan.
These folders all exist but kodi headless doesnt appear to be able to see them. What can i do to get this up and running?
-
I have not restarted in a while, will do that and see what happens.
-
Im getting emails from letsencrypt about my certs expiring soon, do i need to do anything or does it take care of it on its own?
-
Question for everyone. I have been using this plugin for a while but completely missed the setting that allows you to ignore specific file extensions and now when it runs the verification task my .nfo's are almost always flagged as having been modified. Whats my best course of action to prevent getting that every time it runs? Is there a way to remove the hash from a specific file type in batches?
Ultimate UNRAID Dashboard (UUD)
in User Customizations
Posted · Edited by hermy65
Perhaps mine does not have modbus support, cant seem to find it in any menu.