G Speed

Members
  • Content Count

    242
  • Joined

  • Last visited

Community Reputation

2 Neutral

About G Speed

  • Rank
    Member

Converted

  • Gender
    Undisclosed

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. actually it's just an i3 on one of my rigs xmrig off total used free shared buff/cache available Mem: 15884 1906 2546 738 11431 12931 Swap: 0 0 0 Xmrig on total used free shared buff/cache available Mem: 15884 4268 197 738 11418 10571 Swap: 0 0 0
  2. At work right now, I will do when I get home, but to answer some of your question Correct, I have it limited to one numa mode With xmrig off that screen shot would show 15% usage In the docker page, when xmrig is running it's using approx 2.Xgb
  3. * ABOUT XMRig/6.10.0 gcc/9.3.0 * LIBS libuv/1.34.2 OpenSSL/1.1.1f hwloc/2.1.0 * HUGE PAGES supported * 1GB PAGES supported * CPU Intel(R) Core(TM) i3-8100 CPU @ 3.60GHz (1) 64-bit AES L2:1.0 MB L3:6.0 MB 4C/4T NUMA:1 * MEMORY 11.2/15.5 GB (72%) Without XMrig running, i'm only at 15% ram utilization So yeah.. something wrong
  4. What am I doing wrong... In log * HUGE PAGES supported * 1GB PAGES supported randomx failed to allocate RandomX dataset using 1GB pages Settings --no-color --asm intel --randomx-1gb-pages Running privileged
  5. Based on what my CPU should be getting, it looks like MSR is not really holding me back... Intel if that matters As per the 1gb pages... seems like it might not be wroth it For RandomX dataset since version 5.2.0 the miner support 1GB huge pages (regular huge pages size is 2MB), this feature available only on Linux. It increases the hashrate by 1-3% (depends of CPU) and increases memory requirements to 3GB (3 pages) per NUMA node
  6. Thanks for the response, I don't think I said 20A anywhere? 2AMP x 5 - Should draw a max of 10AMP Should be fine, on the wires Why don't you run more than 5? The wire is more than capable? Depending on what your using it for.. Also, I'm not sure I understand the point of the block? Why not run 12v-5v-2 ground, punch down with sata connector. then a few inches down.. continue on THanks!
  7. Just playing around with this now, as per others msr is not working.. also 1GB PAGES disabled It's set as Privileged
  8. I have a modular PSU Can I make my own SATA Cables with just 4 wires, and omit the 3.3V? Since alot of backplanes use molex, and alot of people use molex to sata and run drives just fine, 12v and 5v It would avoid any hassle with shucked drives/3.3V Can I run 5 drives off of a single cable? 18awg cable - 16amps IIRC? Most drives max 2AMPS during full usage?
  9. Mar 27 00:29:53 Servo emhttpd: spinning down /dev/sdd Mar 27 01:04:00 Servo kernel: mpt2sas_cm0: log_info(0x31120303): originator(PL), code(0x12), sub_code(0x0303) Mar 27 01:04:00 Servo kernel: mpt2sas_cm0: log_info(0x31120303): originator(PL), code(0x12), sub_code(0x0303) Mar 27 01:04:00 Servo kernel: mpt2sas_cm0: log_info(0x31120303): originator(PL), code(0x12), sub_code(0x0303) Mar 27 01:04:00 Servo kernel: mpt2sas_cm0: log_info(0x31120303): originator(PL), code(0x12), sub_code(0x0303) Mar 27 01:04:00 Servo kernel: mpt2sas_cm0: log_info(0x31120303): originator(PL), code(0x12), sub_code(0x03
  10. Parity Finished - Rebooted, Started Array. Checksum error is back "so your right I need to stick with parity 2" in my case As for the cables/slots.. I moved the two troubled drives over to the motherboard controller and in a different backplane
  11. Will wait for parity to finish, then get back to you
  12. Mar 22 16:49:06 Servo kernel: mpt2sas_cm0: log_info(0x31120311): originator(PL), code(0x12), sub_code(0x0311) Mar 22 16:49:06 Servo kernel: sd 1:0:5:0: Power-on or device reset occurred Mar 22 16:49:07 Servo kernel: sd 1:0:5:0: Power-on or device reset occurred Mar 22 17:32:01 Servo kernel: mpt2sas_cm0: log_info(0x31120311): originator(PL), code(0x12), sub_code(0x0311) Mar 22 17:32:02 Servo kernel: sd 1:0:5:0: Power-on or device reset occurred Mar 22 17:32:02 Servo kernel: sd 1:0:5:0: Power-on or device reset occurred It has begun.... Same two drives Disk 4 and Disk 7 They share
  13. So this is interesting, I put the parity disk back into slot 1. Then assigned it to Parity 1. Gave me a Blue Square, and said it needs to do a rebuild - Obviously I press start, get that error again.. ALSO I noticed same original problem on Disk 4 Power-on or device reset occurred I shut down the array, reseat drive and replug in all cables etc.. for Disk 4 "no power drive" Start up system, remove parity it goes to unassigned devices, I format as NTFS - takes 5 seconds. I throw it back into array, Parity 1. Asks for Rebuild - ZERO ERROS! Mar
  14. Exactly, I had no issues with my setup. I even recently swapped out a 1tb for a 2tb, and used parity to rebuild. Exact same hardware running 6.8.3 IIRC Worked without a hitch That's why I'm not sure parity 2 is the ONLY way to go